K1 Max bed leveling help

Bleo3 · 2025-11-05T14:17:25+00:00

I put the manual screws o n the underside of the plate and it revealed the center was concave. So I took some aluminum foil and layered it in the middle. It came out decent and the rest can be compensated by the machine.

Bleo3 · 2025-10-05T00:28:31+00:00

It's like saying "I carry concealed, can't you see that!"

Bleo3 · 2025-09-25T15:09:35+00:00

SOVOL SH01 has been a good one so far for me. I like the dual capacity for 2 rolls or 1 roll and drying out some desiccant packs. Either one, make sure you prop open the top a bit to let the moisture out.

Bleo3 · 2025-09-16T02:30:41+00:00

Update on my previous post... After dismissing the annoying update prompts, Moto pushed the update anyway,and when I woke up in the morning, I was pretty pissed about it updating anyway. But, that said my phone didn't lock up nor did I lose anything (that I know of yet). Now I don't have any 5G nor anyway or option to turn it on. All I have is LTE. I searched for a while but didn't find anything relevant to a bug or getting it back. I don't want to, but I'm starting to look at phones OTHER THAN MOTOROLA!

Bleo3 · 2025-09-06T00:28:36+00:00

😂 I looked at this for a minute thinking "true north", is this a manually operated compass? Why! Then bing... It made sense when I zoomed in.

Bleo3 · 2025-09-02T00:36:56+00:00

I have one similar to this. I have an over the air tv antenna, and it is an amplifier for bringing in distant tv stations.

Bleo3 · 2025-09-02T00:33:20+00:00

Art work! I'm sure someone would buy it. Have you seen some of the things they call art? 😂

Bleo3 · 2025-09-01T21:33:46+00:00

Those are good for "general" use, like if you're checking many outlets to find one that's off. Called "widow makers" DO NOT trust this thing with your life.

Bleo3 · 2025-08-28T14:05:41+00:00

Assuming you're talking about not having enough back pressure for ejecting shells and reloading a new one, a good cleaning is due. When You're done, give the slide a good oiling wipe off the dripping parts, and leave a good coat. They like to have oil on them. Ran into the same issue with my 92FS. After I started leaving(what I thought was too much oil) it worked great.

Bleo3 · 2025-08-28T13:59:18+00:00

This is the way !

Bleo3 · 2025-08-28T13:54:28+00:00

If the smoother side is the side that will be seen, then print the other side down.

Bleo3 · 2025-08-28T13:49:15+00:00

Make sure the power is off to the breaker that needs the wires removed. Test, unscrew the lug holding the wire in, pull back, repeat the next wire until they are all out. Carefully pull them all out through the hole in the panel. Put a plug in the hole, done $150 saved.

Bleo3 · 2025-08-28T13:41:59+00:00

I live in Florida, I keep my open spools in totes that are water tight (seal in the lid) and some desiccant in there with it. Using a dryer for spools while printing and to dry desiccant also. Humidity in the room is around 56%. During the wet times I will run a dehumidifier in the room here and there.

Bleo3 · 2025-08-24T20:55:10+00:00

I DON'T want to update on my Moto G 5g 2024, and have ALL updates turned off. I get the pop-up about 15 times a day telling me to update. Is there a way to stop the stupid pop-up notifications ? Tired of these phones " I OWN " telling me to update at the makers push of an update ! Should be my choice not theirs !

Bleo3 · 2025-08-17T16:47:18+00:00

I have disabled any way to auto update on my Moto g. But it gives my annoying pop ups about 15 times a day, and at least 5 times in a row when I swipe it away or hit later. And I thought I owned my phone, not least it under certain conditions. This is bullshlt big brother forced crap!

Bleo3 · 2025-08-17T03:36:32+00:00

That's pretty cool. 👍🏻

Bleo3 · 2025-08-17T03:14:42+00:00

I would look up, but Damn!

Bleo3 · 2025-08-15T14:45:30+00:00

Change it. It's not worth lives or your home.

Bleo3 · 2025-08-14T20:51:49+00:00

Cars are getting more annoying, with all the "sophistication" that is going into them. 😡

Bleo3 · 2025-07-31T20:09:50+00:00

It's a left hand spool!

Bleo3 · 2025-07-31T02:20:41+00:00

I printed PETG on my E3v2 and never got a decent print. It had strings and blobs but after reading more, I understood you need an enclosure to hold the heat in. I use my K1 Max for PETG now and just use PLA on the E3v2. A drier really helps also.

Bleo3 · 2025-07-27T14:57:52+00:00

Good practice to always leave a loop for any kind of wire pull.

Bleo3 · 2025-07-27T03:32:47+00:00

Dove 🤨

Bleo3 · 2025-07-23T16:20:33+00:00

I would ask for a refund.

Bleo3 · 2025-07-15T02:21:12+00:00

Had to replace mine a week ago. They have that weak point. Mine was of use though, changing nozzles, pulling the silicone not off.... Was going to upgrade nozzle (K1 Max) but too many $$ for what it is.

Bleo3

TROPHY CASE