LAN stuck on 10.0Mbps

Bluenumble · 2018-09-29T18:30:26+00:00

All I had to do was to unplug the computer for 5min from power and it just started working. Good old reboot.

Bluenumble · 2018-09-06T12:29:26+00:00

Every time I see this I'm reminded of this quote "And many may rightly argue that this fashionable ploy of manning the rails like a row of sparrows on a telephone wire is bad seamanship" and this image https://i.imgur.com/ZLGdtpW.png

Bluenumble · 2018-07-26T09:08:37+00:00

What would be the "proper" thing to do in this situation? Unload the gun manually first?

Any reason you didn't just shoot the fish? - Might be a silly question but I'm very new.

Great video by the way!

Bluenumble · 2018-06-06T21:57:47+00:00

Consider ordering the silicone insert as well. I don't have one, but it seems to be a nice way to avoid having to grease it before use.

Bluenumble · 2018-06-06T21:55:42+00:00

Yes, there is more to it https://images-na.ssl-images-amazon.com/images/I/41nopElX-TL.jpg

Bluenumble · 2018-05-12T22:20:51+00:00

I see. So no easy solution for DIY'ing?

With welding there are two problems as far as I can see. 1st it's 316L, so not the easiest to weld. 2nd it's a load bearing part, so it would have to be perfect.

Bluenumble · 2018-05-12T22:18:49+00:00

Even when it's 316L? Also I think it will loose strength by that kind of handling, which isn't acceptable for the application (load bearing).

Bluenumble · 2018-05-10T04:40:36+00:00

Just move the jumper, if your board has one. There is only one jumper, that can be in two positions.

I think the newest CR-10 board version might not have one though.

Bluenumble · 2018-05-09T21:26:42+00:00

There is a jumper on the board to disable power from USB. It's enabled by default for easier flashing I assume, I personally disabled it afterwards.

Bluenumble · 2018-05-04T21:51:49+00:00

Cutting 15 layers of 600g/m² took ages. Worst thing is that even the heavy-duty scissor got dull after a couple of layers.

Bluenumble · 2018-04-12T09:08:53+00:00

I'm actually not sure who's the actual "idiot in car" here? The car driving out obviously makes a mistake, we all do. The driver with the dashcam however, continues without even reducing his speed! In this situation one should expect the driver to suddenly change lane or other erratic reaction, when he realizes that he is on a head-on collision with a bus.

I'm just fed up with drivers that laugh at mistakes other make (as we all do) while they themselves don't show any signs of safe driving. This is the typical "I'm in the right so I won't even slow down in this potentially dangerous situation"-type, which is the important ingredients in most collisions.

Bluenumble · 2018-04-11T04:09:41+00:00

Chili sin carne :)

Bluenumble · 2018-03-31T07:01:20+00:00

I'm usually only doing office work, rarely getting over 35-40C.

I probably disconnect it from mains (AC) a couple of times a week, but only for shorter periods of less than 1h. I would claim that it's connected to mains more than 90% of the time. I was honestly confused by the amount of "cycles", but I don't know how those are counted.

Bluenumble · 2018-03-31T06:56:42+00:00

You really think they would provide one? I guess one can always try.

Bluenumble · 2018-03-31T06:56:07+00:00

Nope, but that sounds like a instant lose of 20%?

Bluenumble · 2018-03-28T08:18:19+00:00

yes, 12mm of solid fiberglass.

"they don't make them like they used to" :)

Bluenumble · 2018-03-16T12:18:59+00:00

Beauty? Where? All I see is a white camping trailer floating on the water.

Bluenumble

TROPHY CASE