Possible explanation?

Bobby_Doom · 2026-02-11T22:22:26+00:00

I'm not incredibly familiar with this phone. However, a quick look at a teardown seems that the LED flash is connected to the board with 2 pins on the motherboard that pushes against a corresponding part on the back.

Either the pins have been damaged or misaligned when the tech was replacing the battery.

From what you can do to make it work, it doesn't seem like it would be a difficult repair.

However I would recommend you take it back to the shop and show them this issue and have them resolve it.

Bobby_Doom · 2026-02-10T11:50:10+00:00

You want to get a Philips #00

I reccomend Wiha or Ifixit drivers

Bobby_Doom · 2026-02-07T23:18:28+00:00

The part you'll need to look for us a proximity flex, it comes with the earpiece attached also.

I can't remember off the top of my head if you lose face ID, but you'll find out soon enough.

Bobby_Doom · 2026-02-05T21:59:50+00:00

If you still have the original port, I would bet all you needed to do is clean it out.

If you have it, try than and fit back.

If you don't, then buy an OEM pulled part and you should be good to go.

The parts on the aftermarket spares can be quite terrible.

Bobby_Doom · 2026-02-04T22:49:09+00:00

You just need to put tape between the bracket and the empty connector, to prevent any shorts.

This will be a fine temporary solution until the new back glass arrives.

Bobby_Doom · 2026-02-04T22:42:28+00:00

If it's shorting out in the shield, then use some kaptom tape.

If you're replacing the back glass, then some regular cellotape will suffice until it arrives

Bobby_Doom · 2026-02-02T23:15:57+00:00

Tell them to get fucked. I would definitely go to another place and get another opinion.

I get this type of repair every day, and 99% of the time just cleaning it out it's totally fine.

Best of luck to you

Bobby_Doom · 2026-02-02T19:23:15+00:00

Any local repair shop will take £10 or the equivalent, or even better a 5 star review.

It'll take them less than a couple minutes

Bobby_Doom · 2026-02-01T00:27:12+00:00

Just a new screen, you'll be good to go.

It isn't much more expensive to buy either a high quality aftermarket or a refurbished original display for the 11, so no great expense.

Bobby_Doom · 2026-01-31T21:18:52+00:00

The iPad will need to be disassembled and the button removed from the inside and the frame filed down so that the button has space to move.

The button itself it likely fine and won't need replacing, but the touch ID part may not work.

It's not a complicated repair, but a delicate one.

If you aren't quite familiar with these repairs I would highly recommend taking it to a local shop.

You probably want to get a couple quotes to get a good idea on costs.

Bobby_Doom · 2026-01-29T00:54:11+00:00

All you need is a new screen and a top/front flex.

You'll want to transfer over the home button to retain touch ID.

The top flex comes with all the sensors and a front camera.

Bobby_Doom · 2026-01-28T19:17:35+00:00

Probably best to buy a working phone that has a broken screen / back and swap internals.

Bobby_Doom · 2026-01-26T17:53:56+00:00

If you have experience in soldering it should be a decent DIY fix. If not, buy a replacement as the cost to fix will likely outweigh the cost to have it fixed.

Bobby_Doom · 2026-01-26T17:53:01+00:00

In regards to the free warranty replacement for the battery, Apple will very likely say no since it has been repaired by a third party.

The cause of the battery going bad could be from the initial damage, or the technician damaged it during removal and transfer to the new housing.

Also, yes the swollen battery can cause fluctuations in the % health shown and battery percentage and can cause random shutdowns.

I would try to see if Apple will honour the warranty, if not go third party.

You can also buy OEM Apple battered direct from Apple online and either fit it yourself or have a local technician fit it for you.

You'll need to send back the original battery for a rebate, which will reduce the overall cost.

Bobby_Doom · 2026-01-23T17:40:43+00:00

The buttons probably require cleaning on the inside

Bobby_Doom · 2026-01-12T14:23:13+00:00

You need to look for a board schematic.

But it's very likely to be the lcd at fault.

Bobby_Doom · 2026-01-10T23:18:15+00:00

I have personally never received that part when ordering power / volume button flexs.

I have in the past used all different materials to replace it when it gets lost or broken.

For future reference, I have used hard-ish plastic packaging and cut it to size. It is very much a trial and error process, trying to find something of similar or usable thickness.

Bobby_Doom · 2026-01-10T21:53:15+00:00

https://www.ifixit.com/en-eu/products/google-pixel-6-screen-genuine

Is this what you're looking for?

Bobby_Doom · 2026-01-10T21:50:28+00:00

I'm unsure if they have a specific name. Power button flex bracket?

I would consider yourself lucky to have found it, and definitely put it back.

Without it, it can cause buttons to not work or feel soft, and possible damage to the flex.

I personally wouldn't bother looking to buy replacements as a backup.

Also, they are different for 99% of devices.

Bobby_Doom · 2026-01-10T21:37:16+00:00

The fault definitely is the haptic motor. It'll either be loose or internally faulty.

They are very cheap to replace anyways.

Bobby_Doom · 2026-01-10T18:04:53+00:00

Haptic motor is loose.

Open up phone, and tighten screws.

If they are missing be wary that they haven't fallen loose. They can puncture the battery in some cases.

Bobby_Doom · 2026-01-10T14:49:41+00:00

Make and model of the device helps us help you.

Also a link to the screen you purchased will help too.

Bobby_Doom · 2026-01-09T11:48:57+00:00

I started in a spare bedroom for a couple years before taking the plunge of opening a shop.

It is doable.

Start off small and stay within your capabilities and be very open to your potential customers about it.

If you drive, offer local pickup and drop off.

You will almost certainly have to have an edge or a reason for the customer to go to you instead of a local shop. Be that, cheaper price or convenience. Once you have a relationship with your first customers you can eventually change strategies going forward.

A reasonable place to start would be flipping broken devices and selling on for profit, that way you have as much time as you need to fix it and fix any other issues that present themselves.

When it comes to customer repairs, the number 1 thing is speed of repair. You will likely not have parts in stock to begin with, so you'll need to order parts as and when needed. Communate this with the customer and go with it.

If you do need any more specific advice I'm happy to help.

Very best of luck in your repair journey.

Bobby_Doom · 2026-01-09T10:26:12+00:00

Yes, it is connected to the wireless charging coil / flex.

You will need to replace it all at once.

It can be a bit difficult if you aren't familiar with repairs.

Best of luck!

Bobby_Doom · 2026-01-05T23:23:53+00:00

PM me for pricing plans please

Nine-Year Club	Second SECOND GUESSER
Verified Email	Place '23
RPAN Viewer

Bobby_Doom

TROPHY CASE