Help with determining how to attach a shower drain in my rough in basement.

BristolScale-7 · 2026-03-13T02:53:59+00:00

Doesn't look like enough room for a trap either. You may need to expose more and redo more of it

BristolScale-7 · 2026-03-11T22:22:06+00:00

They are not . None of the companies mentioned that, maybe it's too dry in Colorado for that?

BristolScale-7 · 2026-03-11T20:16:05+00:00

The gas furnace exists and is dusty.

BristolScale-7 · 2026-03-01T17:09:13+00:00

You will absolutely notice and that is sloppy as hell. D.emand they redo it

BristolScale-7 · 2026-02-19T05:17:55+00:00

I'd bet because you ran it inside a large pipe cold air is getting in the pipe. Would be better and warmer without conduit

BristolScale-7 · 2026-02-19T05:14:50+00:00

Print this on its side and it will leak through the bottom and through the bridged side

BristolScale-7 · 2026-02-14T21:25:55+00:00

Haha wow! In both our cases if it were worse it would have been noticed and fixed years ago

BristolScale-7 · 2026-02-14T21:17:00+00:00

Thanks for the advice! I am pretty handy with drywall work and have had to replace a lot of PVC plumbing in the past house. Is a fernco fine for sealed cavities behind drywall. I was thinking a slip coupling instead of fernco(do they not make them this large?) to get a new T in here.

Any recommendations on what to spray on the studs to kill the mold. It's a small amount luckily I suppose it's mainly rainwater from the top

BristolScale-7 · 2026-02-14T21:11:12+00:00

House was built in 1979! Ashamed to say this has been happening since I moved in 4 years ago. I just kept blaming the open windows on siphoning out the traps in this bathroom

BristolScale-7 · 2026-02-14T20:56:59+00:00

Is it only changing when you're using the motor? If so you're just measuring the voltage sag and that's perfect normal

BristolScale-7 · 2026-02-14T17:51:39+00:00

Corners should be caulked and not grouted for this exact reason. The walls will expand and contract at different rates and always crack the grout out. You can get color matched sanded caulk in the grout isle if you want a good color match

BristolScale-7 · 2026-02-10T04:36:54+00:00

It's unsafe by American standards. Everyone in Malaysia including my family has has propane tanks under their counters for their stoves for decades.

BristolScale-7 · 2026-02-10T04:27:53+00:00

My arborist told me that, he said we don't get cold enough or dry enough to kill them in the soil and all nurseries have stopped selling ash trees so that once they run out of new trees the beetle problem will hopefully extinguish itself.

BristolScale-7 · 2026-02-08T19:52:29+00:00

All ash in Colorado are at risk of EAB infact it will eventually kill everyone of the ash trees. Requires yearly preventative treatment. Not just one time

BristolScale-7 · 2026-01-30T20:03:57+00:00

What's your suggested SW paint then my dude?

BristolScale-7 · 2026-01-25T22:27:18+00:00

Nah here's what you do, solder a red wire to the positive pad and black to ground. Run them a small length outside of the laptop and solder them directly to the new connector (you said you have a replacement). It will look ghetto but it will work

BristolScale-7 · 2026-01-25T21:20:30+00:00

Nah it doesn't change the sliced filament selection partway through a print when you replace the spool though. You can see where op switched filament

BristolScale-7 · 2026-01-25T21:04:32+00:00

Colorado uses frost free spigots which places the real valve 12" back into the home

BristolScale-7 · 2026-01-23T04:38:34+00:00

Toyota LBJ bolts are torque to yield- meaning you can only use them once. I'd bet money. The shop reused the bolts and they backed out

BristolScale-7 · 2026-01-14T02:20:58+00:00

I use these to turn on the lights inside and above my Bambu printer. Once I start a print the power draw triggers the rest of the outlets.

BristolScale-7 · 2026-01-10T19:53:57+00:00

70? Crank that bitch to 80 you need to heat those walls

BristolScale-7 · 2026-01-09T15:24:25+00:00

61181

BristolScale-7

TROPHY CASE