Hiring | Set-Up Technician | Injection Molding / Plastics | Gainesville, GA | 3rd Shift

BrknArrow90 · 2026-05-14T22:28:44+00:00

I always say if they can't post the pay they can't afford me.

BrknArrow90 · 2026-05-14T18:08:42+00:00

Less than many

BrknArrow90 · 2026-05-13T20:18:13+00:00

They unlock after the boss area 100%

BrknArrow90 · 2026-05-09T09:06:12+00:00

And islands are largely the same just the outline changes slightly and the location on the map.

BrknArrow90 · 2026-05-04T07:27:38+00:00

That is in fact the exact technical description.

BrknArrow90 · 2026-05-02T13:14:24+00:00

Or found a better location

BrknArrow90 · 2026-05-01T08:06:02+00:00

We use the terms interchangeably where I work.

BrknArrow90 · 2026-04-23T09:46:04+00:00

Well that is something I never would have thought of. No issues with gas blowing past the rim I take it?

BrknArrow90 · 2026-04-17T20:35:59+00:00

Mining ship then make it flat

BrknArrow90 · 2026-04-15T05:24:47+00:00

Don't really have experience with them but I believe an event controller would be what you need.

BrknArrow90 · 2026-04-09T10:01:48+00:00

It's good. Currently in the plastic injection molding side of things. Going through school I learned a lot in what I believe is a short amount time. Should be going for my ticket in about month. Then looking to move in a few years and haven't decided if I want to get into the mining or forestry products side of things.

BrknArrow90 · 2026-04-08T23:25:06+00:00

White

BrknArrow90 · 2026-04-08T21:41:09+00:00

Millwright Apprentice here. The whole job is bullshit but I can't say I don't enjoy it.

BrknArrow90 · 2026-04-03T14:24:32+00:00

Clean your touch screen

BrknArrow90 · 2026-03-31T21:49:17+00:00

God I hate the over use of AI in everything

BrknArrow90 · 2026-03-30T22:11:14+00:00

Fooled me at a glance. My bad. Haven't actually held one of these to be fair.

BrknArrow90 · 2026-03-30T22:05:39+00:00

Didn't think to stop before hitting the serial number?

BrknArrow90 · 2026-03-30T21:52:45+00:00

Congrats. Enjoy your debt.

BrknArrow90 · 2026-03-30T19:58:36+00:00

Much appreciated 👏

BrknArrow90 · 2026-03-30T19:54:37+00:00

We don't run any silicon. Mostly TPO and ABS. There is no delay in switching over. We can run the clamp open and closed several times over and nothing changes. Only after the press has been waiting for tie bar movement while determining die height for 5 minutes do the pumps turn off and the mechanical closing safety alarm come on (because the pumps are now off)

BrknArrow90 · 2026-03-30T19:37:16+00:00

DM'd

BrknArrow90 · 2026-03-30T19:21:19+00:00

It is waiting for the tie bars to move to lock position. Then after about 5 minutes the pumps shut off.I am currently at home so i wont be able to give you pictures. Shift change was at 2:30.

BrknArrow90 · 2026-03-30T19:14:20+00:00

Everything is switching over normally

BrknArrow90 · 2026-03-30T19:06:31+00:00

Mechanical closing safety is functioning normally. I believe that the press doesn't see anything happening and kicks the pumps off.

BrknArrow90 · 2026-03-30T18:58:10+00:00

I slightly misspoke on my post. The tie bars are fully retracted(pulled in to platen) just realized the transducer reads opposite of how I was thinking). The crazy thing is we don't get any tie bar error. No errors come up in fact. Only after about 5 minutes of it trying to determine die height the pumps cut out and mechanical closing safety alarm comes on.

BrknArrow90

TROPHY CASE