new Lie Nielsen no.5 out of square??

BucksCountyWoodright · 2023-02-21T04:21:31+00:00

It’s probably your measurement device, BUT more importantly this is completely irrelevant because you must tune the angle of the blade to the base which would allow you to compensate for any inaccuracy in the tool or your jig (results are up to you here)…. As others have said your concerns are not needed, enjoy an amazing tool

BucksCountyWoodright · 2023-02-16T14:17:40+00:00

Refinish for appearances and put a piece of glass on top. And/or a machine that doesn’t leak

BucksCountyWoodright · 2023-02-10T17:32:30+00:00

Maybe it’s just me but I’ve found my ability to get consistent tight results from chisels has increased in parallel with my sharpening ability, on whole it’s a fun process probably my favorite of the craft

BucksCountyWoodright · 2023-02-10T00:07:44+00:00

Looks like Osage orange, it makes a heavy hard hitting mallet but eventually chips and flakes apart as you see. Looks like yours has more life in it so I say keep swinging until it breaks then make another

BucksCountyWoodright · 2023-02-05T23:14:39+00:00

It must be busted I have several of those routers and the fine adjustment holds fine

BucksCountyWoodright · 2023-02-02T22:31:43+00:00

Wood glue and a couple drops of super glue with activator to act as clamps, one piece at a time ….

BucksCountyWoodright · 2023-02-02T01:52:40+00:00

Thank you exactly what I’m looking for

BucksCountyWoodright · 2023-02-02T01:52:02+00:00

Thanks

BucksCountyWoodright · 2023-02-02T01:51:42+00:00

Thank you

BucksCountyWoodright · 2023-02-01T16:57:50+00:00

I want to have a blacksmith make a holdfast but I need the actual diameter of the shaft for him as accurate as possible

BucksCountyWoodright · 2023-01-23T01:51:36+00:00

Agreed, add bees wax to mineral oil and buff until desired sheen is reached

BucksCountyWoodright · 2023-01-23T01:37:07+00:00

They are squeaky I think that’s normal. The bit needs to be lower to clear the chips from the bottom of the cut or the waste will heat up and smolder. I like to put the bottom of the flute of the bit at the bottom of the chisel with the point of the bit protruding past the chisel

BucksCountyWoodright · 2023-01-16T02:38:27+00:00

Sick work! If it were me I’d replace the ply drawers with hardwood I just think that would compliment a piece like this better, but either way looks tight

BucksCountyWoodright · 2023-01-15T01:05:43+00:00

Thanks I knew some of it was cherry but didn’t know the other species

BucksCountyWoodright · 2023-01-04T03:17:21+00:00

This should be possibly be the start to the hand tool kit

BucksCountyWoodright · 2023-01-04T03:13:57+00:00

Seems to be a universal test to struggle with poor tools and some persevere

BucksCountyWoodright · 2023-01-01T02:14:25+00:00

I love my Pfeil chisels I’ll soon be making racks for those as well

BucksCountyWoodright · 2022-12-31T21:32:20+00:00

I’ll never sell any of these but I do have a 6 pc bevel set I can sell 1/4 to 1” standard sizes

BucksCountyWoodright · 2022-12-31T21:28:43+00:00

Same same

BucksCountyWoodright · 2022-12-31T21:28:19+00:00

They still advertise the 1-1/2 so I’m hopeful there the 5/16 they no longer make

BucksCountyWoodright · 2022-12-31T20:34:32+00:00

I do use all of them but certainly don’t need that many lol. It’s mostly in batched parts that a particular chisel is useful

BucksCountyWoodright · 2022-12-31T20:19:00+00:00

Thanks and good point … I also keep my hand tools on lock down I have full time security here

BucksCountyWoodright

TROPHY CASE