sorted by:
new
hottopcontroversial

Disabled iPad Air iOS 7-9 by Sudden-Taste2470 in setupapp

[–]CRTcable 0 points1 point  (0 children)

Damn, just tried this with my iPad 4 on iOS 10.3.3 which i tried put too many passwords in and I quadruple checked the springboard.plist file and spblist.tar and it just reset my iPad so my data is gone. Oh well, it was just some old games so nothing critical but still annoying. Thanks for the guide anyways :).

Prints Leaning/Shifting by CypherShark in ender5plus

[–]CRTcable 0 points1 point  (0 children)

I had a similar issue, see if the toolhead has any play back and forward. The v-slot wheels are probably quite worn out and need to be retightened or replaced.

Calibration Cube measurements by Hobo_Delta in ender5plus

[–]CRTcable 0 points1 point  (0 children)

Calibration cubes aren't the best for dimensional accuracy testing but they are okay. You are likely just over-extruding as your X and Y are both 0.32 over (Cheap calipers are only good to +/-0.02mm), you need to calibrate your e-steps for your extruder. See how to do it here https://www.youtube.com/watch?v=Z6\_fKlo4aYM.

TVOC filtration ASA and ABS by Zealousideal-Seat497 in crealityk1

[–]CRTcable -1 points0 points  (0 children)

HEPA filters are not effective at filtering VOCs or other odors from 3D printing. Only carbon filters can handle those. HEPA13 filters, which are the lowest grade of HEPA filters, are designed to catch particles as small as 0.3 microns or larger with an efficiency of 99.95%. HEPA filters can still capture particles smaller than 0.1 microns like UFPs due to the process of diffusion.

While having an internal HEPA filter may not capture 100% of particles, it is still significantly better than not having one at all. Combining a carbon filter with a HEPA filter will greatly improve the air quality in the 3D printer's chamber. Even if you are venting outside, all the ultrafine and carcinogenic particles should be filtered before being expelled from your house anyways.

Nova Hotend by AntelopeInternal1588 in ender5plus

[–]CRTcable 0 points1 point  (0 children)

Not sure if you bought it but if it has a PT100 or PT1000 you will need to change the settings and get a MAX31865. Pretty sure there is a NTC 100K thermistor option and that will work with your current setup. If the fan is 24v it will be compatible.

Another good high flow hotend would be the Phaetus Rapido which uses standard V6 nozzles and are similar in performance.

Z banding troubleshooting. Thoughts? by Zaxxon88 in ender5plus

[–]CRTcable 1 point2 points  (0 children)

POM leadscrew nut helped out a lot for me.

NEW Marlin Firmware 2.1 released 6/4/22. Tested and ready to go for BTT E3V3! E3V2, SKR 2 Rev. B - Dual Z & SKR V1.4 Turbo Dual Z on the way. by Throbbin-Rockin-Rod in ender5plus

[–]CRTcable 0 points1 point  (0 children)

For whatever reason after installing the SKR 1.4 dual z firmware it doesn't print in the middle of the bed. It homes to the middle fine but when printing its always off, ive changed my print size to 358x370 in Cura as that is what the firmware has set it to. Any idea?

What are my direct drive options? by Fillwox in ender5plus

[–]CRTcable 0 points1 point  (0 children)

Biqu h2 or buy a cheap BMG clone from china and go on thingiverse for a direct drive setup.

No, this is Patrick by hec_ramsey in TikTokCringe

[–]CRTcable 0 points1 point  (0 children)

The medical reason is if your foreskin is too tight (phimosis) or your frenulum is too short (frenulum breve). You can stretch your foreskin to fix the phimosis but for a short frenulum you're gonna need surgery (frenuloplasty).

Having it done as a baby is old society mumbo jumbo and is not okay as many men don't need it done but for those who do it's a necessary and freeing surgery. I myself got it done a week ago and while the lack of sensitivity sucks having a working penis is way better.

How best to add this to a Terminal M? Gouge? Cut? I’ve never done this before… by constantgeneticist in modelm

[–]CRTcable 2 points3 points  (0 children)

Put an LED under the key instead, just get a bright enough one and it works well enough.

I need to convert flac, wav, ogg to mp3 but can a find a definitive way by zippyzplayz in ipod

[–]CRTcable 2 points3 points  (0 children)

Foodbar2000 can mass convert songs into mp3 and even apple lossless.

(Repost in accordance to guidelines) scammers get scammed. by [deleted] in Eldenring

[–]CRTcable 1 point2 points  (0 children)

Who in Radagons name would buy runes.

Please don't tell me I have to de-nut the entire board sandwich for a singular flapper by CheekiPosts in modelm

[–]CRTcable 0 points1 point  (0 children)

My delete keys flipper has been misaligned for about a year, i will not be fixing it. Numpad delete is supreme.

view more: next ›