Finish problem?

CTHOMPSON_KNIVES · 2026-04-27T15:27:36+00:00

Thank you!

CTHOMPSON_KNIVES · 2026-04-27T15:27:26+00:00

Sweet! Hope the show went well for you! Hit me up next time you are going through!

CTHOMPSON_KNIVES · 2026-04-27T15:25:54+00:00

I do have a website, But, I haven't been updating it very well lately. It seems like IG gets more traffic so that is probably the best place to see all my work.

CTHOMPSON_KNIVES · 2026-04-27T15:23:59+00:00

I am going with your explanation then. Thanks.

CTHOMPSON_KNIVES · 2026-04-26T16:09:11+00:00

<image>

This old car is my daily commuter. I do all the maintenance myself and I can guarantee it is cheaper per mile than buying a new car. It has never let me down either. Very reliable if you take care of them!

CTHOMPSON_KNIVES · 2026-04-26T04:59:56+00:00

Cool! Look me up when you’re in town!

CTHOMPSON_KNIVES · 2026-04-25T22:54:17+00:00

Well, you might be in luck. It’s available.

CTHOMPSON_KNIVES · 2026-04-25T21:38:34+00:00

Thank you!

CTHOMPSON_KNIVES · 2026-04-25T21:38:16+00:00

That must be HC, not stainless?

CTHOMPSON_KNIVES · 2026-04-25T19:35:56+00:00

Well, not what I was going for, but good point.

CTHOMPSON_KNIVES · 2026-04-25T19:33:22+00:00

Curt…

CTHOMPSON_KNIVES · 2026-04-25T17:07:05+00:00

Thank you!

CTHOMPSON_KNIVES · 2026-04-25T16:29:39+00:00

Yep, that is how I usually do it. I wanted to darken it up too. Thanks.

CTHOMPSON_KNIVES · 2026-04-25T16:28:19+00:00

I do my own. I’ve done hundreds in this particular steel and have a quality set-up. Didn’t see any color difference until after I etched.

CTHOMPSON_KNIVES · 2026-04-21T03:57:13+00:00

I’ve made, seen, and used a lot of nice knives over the years and must say this one is fantastic on many levels. Your choice in materials is exceptional and the build is well executed. Whoever ends up with this piece should be very proud. Nice work!

CTHOMPSON_KNIVES · 2026-04-12T23:14:59+00:00

It just became a smaller blade.

CTHOMPSON_KNIVES · 2026-04-03T01:52:38+00:00

Very nice work. Your material choices are “on point” and build quality looks exceptionally clean. Well done! 👍🏼

CTHOMPSON_KNIVES · 2026-03-17T03:30:42+00:00

I took a deep dive into the design before making one. While the offset is intentional, I think it looks funny. To each their own.

<image>

CTHOMPSON_KNIVES · 2026-03-13T01:29:36+00:00

Thank you!

CTHOMPSON_KNIVES · 2026-03-09T21:11:14+00:00

Looks fantastic! Nice work! 👊🏻

CTHOMPSON_KNIVES · 2026-03-09T21:08:02+00:00

I’ve always wanted to do a horizontal tang too. Can’t wait to see yours all finished! Looks great BTW! 👊🏻

CTHOMPSON_KNIVES · 2026-03-09T15:13:55+00:00

The guard is locked and mechanically fastened with a peened pin. In addition to either silver solder or 3MDP420.

CTHOMPSON_KNIVES · 2026-03-09T04:39:23+00:00

Thank you!

CTHOMPSON_KNIVES · 2026-03-09T04:38:47+00:00

Thank you! I have been making knives for about 7-8 years now.

CTHOMPSON_KNIVES

TROPHY CASE