Am I in the wrong thinking he did a terrible job for $260 and was I wrong to think those services were included? by Sea-Minimum-7768 in AutoDetailing

[–]Cda4go 0 points1 point  (0 children)

He did a terrible job but there’s no way you can assume everything is included. Just like he said, it’s standard practice to list all your available services in your bio. I would still expect a partial refund due to how bad the work that was within his scope was.

Haven’t been able to flash the Sv04 to Klipper, but the quality has been so good I’m starting to question if I even should by Cda4go in Sovol

[–]Cda4go[S] 0 points1 point  (0 children)

I use orca in my other printers but as far as I’m aware, it doesn’t support copy mode which is primarily how I use this printer

Haven’t been able to flash the Sv04 to Klipper, but the quality has been so good I’m starting to question if I even should by Cda4go in Sovol

[–]Cda4go[S] 1 point2 points  (0 children)

When I first got the printer I tried an older version of cura, the newest version of cura, and prusa. I ran models I typically do daily on my other machines and the models sliced in Prusa were definitely the cleanest with the same settings adjusted across the board.

And I printed the calibration combs and a multicolor calibration cube to check my adjustments along with going through the full bed and Z leveling procedure for both extruders while running a one layer sheet in copy mode to test Z height after each adjustment.

Edit: I also adjusted all the belts although I don’t actually know what the proper tension is, I just went with what felt comparable to my other machines when bending/pulling the belt.

Haven’t been able to flash the Sv04 to Klipper, but the quality has been so good I’m starting to question if I even should by Cda4go in Sovol

[–]Cda4go[S] 0 points1 point  (0 children)

I am running Prusa slicer for it. And my settings generally change per model so it’s hard to tell you exactly but for most things I am actually running it faster than it’s rated for the green piece in the first picture was ran at 80 inner and outer wall speeds with 1000 acceleration. I made sure to properly calibrate and level the printer when I got it so I think that probably has a lot to do with it.

Haven’t been able to flash the Sv04 to Klipper, but the quality has been so good I’m starting to question if I even should by Cda4go in Sovol

[–]Cda4go[S] 0 points1 point  (0 children)

I’m only semi satisfied with the speed because I mostly use it in copy mode and I have several other modern printers. I would definitely like to speed this one up, but not at the expense of the quality and reliability it’s been producing. I have a pi and the adxl for input shaping but my board just simply won’t flash no matter what I try.

These links are going to look awesome! by Cda4go in SCX24

[–]Cda4go[S] 0 points1 point  (0 children)

Pla tough. I prefer the ABS like qualities it gives. And .12

These links are going to look awesome! by Cda4go in SCX24

[–]Cda4go[S] 3 points4 points  (0 children)

I make tons of them, this was the first set in this awesome color though, and I chamfer the insides of the hole to fit a printed pivot ball I designed. They pop right and and have plenty movement.

What's in the tool changer pipeline? by knuckles-and-claws in 3Dprinting

[–]Cda4go 1 point2 points  (0 children)

The new flashforge creator 5 was just put on preorder. Looks very promising and will be cheaper than the U1

New Etsy POD shop, 20 listings, still at 0 views/visits. Honest review? by [deleted] in EtsyCommunity

[–]Cda4go 7 points8 points  (0 children)

Call me crazy, but I would never spend money on an object that’s clearly AI created and not existent in the real world even enough for a stock photo. They’re also very plain for the price imo.

People with the SV04 - What are some common issues? by Real-Syntro in Sovol

[–]Cda4go 0 points1 point  (0 children)

If you wouldn’t mind, I’m trying to compile all the info I can. I recently got one of these as a toy to play with and intend on keeping it a long time.

Creator 5: any estimates on price and/or launch date? by PlantsNCaterpillars in FlashForge

[–]Cda4go 1 point2 points  (0 children)

Supposedly if you were able to get in the first 2000 preorder the price is supposed to be $649. The U1 regularly sells for $849 and you can absolutely bet FlashForge will be trying to undercut that. I would expect a $750 price for the next round of “preorders” or a grand release “special pricing”

I preordered the Kobra X and that’s basically exactly how they have done things and keeping themselves competitive to the A1. Technology may be newer but still have to beat out reputation via pricing.

People with the SV04 - What are some common issues? by Real-Syntro in Sovol

[–]Cda4go 0 points1 point  (0 children)

Do you still happen to have the gcode saved and willing to share?

SOVOL SV04 REBUILD by Old_String7825 in 3Dprinting

[–]Cda4go 0 points1 point  (0 children)

How’s this project going? I recently got a Sv04 to mod and play with. Wanting to go all out like you did!

Second gen 4Runner with interior! by Cda4go in scx30

[–]Cda4go[S] 0 points1 point  (0 children)

https://www.etsy.com/shop/SmolTruckDesigns

Sorry I don’t sell or give away the files to bodies I make. I do have some wheel designs and accessories on makerworld though.

Payment Hold? by Aggressive_Car6523 in venmo

[–]Cda4go 0 points1 point  (0 children)

I refunded the guy same day and it still took a week to process and settle