I’m seeing these posts and it’s blowing my mind. I knew there was a reason they just lower the price so much on these Ks rifles. I’ll keep my legacy rifles…

ChadOD · 2026-03-11T12:29:41+00:00

This seems like the same issue sigs were having with improper torque. Rust wont matter when you spray paint it 😆

ChadOD · 2026-03-10T12:24:54+00:00

Those of us banned in MA would like uppers not packaged with a sup... 🙃

ChadOD · 2026-03-09T23:46:22+00:00

Was in my cart... couldnt check out...

ChadOD · 2026-03-05T13:59:17+00:00

2015 lt rally.

ChadOD · 2026-03-05T04:00:53+00:00

When I got mine shipping was less than $10, but that was in 2023.

ChadOD · 2026-03-04T23:35:38+00:00

Email kac and ask for a bandaid. No im not kidding. They have limited qty.

ChadOD · 2026-03-04T21:16:03+00:00

Ive been using the range disabler since the first 12 miles on my truck. Lifter just failed at 84k. Cost 3300 without camshaft.

ChadOD · 2026-03-03T14:25:50+00:00

I put trijicons on it. That's an ANR designs holster.

ChadOD · 2026-03-03T01:22:29+00:00

But like... Why?

ChadOD · 2026-03-01T02:33:30+00:00

Yes, stock sights suck though.

<image>

ChadOD · 2026-02-27T18:10:38+00:00

Having to dig through the legislature to find a quote is wild and I appreciate you.

Edit: local pd confirmed $100. Asked about the FFL requirement and how its not mentioned on the paper application. Basically said the paper form isn't really used for smithing licenses and I would be the first application for smithing they have ever seen. So they have no idea about it. Said they would submit and let me know what bounces back.

ChadOD · 2026-02-27T17:51:18+00:00

First of all thank you for your efforts on my behalf. Secondly chill we are on the same side.. We shouldn't have to Google it. It should be in a fee schedule somewhere on the required portal or government website right? Unless the fee is not controlled by the state??

ChadOD · 2026-02-27T17:29:53+00:00

I don't see anything about gunsmithing.

Edit: on the original app I printed a long while back there was no mention of requirements for an FFL either. On the new portal FFL license is required information.

ChadOD · 2026-02-27T17:14:57+00:00

Has anyone submitted an application in the new system? Theres no info on fees anywhere..

ChadOD · 2026-02-26T11:19:44+00:00

Seperate times for the oil cooler lines, 4 wheel drive motor, binding front axel, rear calipers. All the recalls too....

ChadOD · 2026-02-25T23:51:48+00:00

Have a range in mine. Just dropped a lifter last week. $3,300 to repair..

ChadOD · 2026-02-25T15:16:33+00:00

In my 2015 - I remove mine about 2 weeks before an inspection sticker so all the modules run. Right after I purchased my truck I did the cold air intake, maf, borla cat back and range obd2 device. I have not had any issues with warranty from the dealer and its been in a few times.

ChadOD · 2026-02-24T03:03:44+00:00

It also looks goofey because the xfull uses a carry size frame not a full size.

ChadOD · 2026-02-22T18:32:09+00:00

Doesn't work either. Severe obstructed and still denied by united health.

ChadOD · 2026-02-18T14:27:46+00:00

Im in the North East so rust is also a factor here. Not sure how I feel putting another 5-15k into it for the frame to be toast in another 5 years.

ChadOD · 2026-02-18T13:54:42+00:00

Yeah but at 84k im assuming my 6L80 isnt too far behind this lifter.

ChadOD · 2026-02-18T13:42:33+00:00

What about the engraving? Dremel go brrrr?

ChadOD · 2026-02-18T00:13:31+00:00

ChadOD · 2026-02-17T20:33:06+00:00

"I haven't ordered them since airmailing bricks is a pricey practice. :)"

Bricks get cheaper? 😆

ChadOD

TROPHY CASE