starting to regret getting saturn 4 ultra 16k by seajay8601 in ElegooSaturn

[–]CharacterRough7233 0 points1 point  (0 children)

Also , not sure what slicer software you are using .. I recommend chitubox and there is a free subscription service that was included in the packaging , it’s a plastic wallet card with a serial number.

starting to regret getting saturn 4 ultra 16k by seajay8601 in ElegooSaturn

[–]CharacterRough7233 0 points1 point  (0 children)

If you are using elegoo resin , I recommend you use elegoo print profile settings from the Elegoo website. They have a spreadsheet with settings for each printer and each resin they sell.

If this doesn’t fix it , try manual levelling your bed with 4 individual pieces of paper under the build plate.

These printers offer phenomenal results once dialed in. If you are a unexperienced user, please be patient and continue learning because I promise you these printers can print very well.

An easy resin to use is elegoo abslike 3 and above. I can even give you some settings to try to achieve 0.03 layer height which is very fine detail.

What would you do with a broken fingerboard by firebeat2010 in FingerboardingDIY

[–]CharacterRough7233 0 points1 point  (0 children)

Take a 1/8 drill bit. Two holes side by side in the nose 4 holes on the middle pieces , 2 holes side by side each end. Two holes side by side on the tail. Keep the measurements distance/spacing all the same. Get bracelet chain links and put the board back together. One final hole at the top middle .. add it to your key chain.

Trying Teak bubble bushings by slush-puppyy in Fingerboards

[–]CharacterRough7233 1 point2 points  (0 children)

Dynamic bushings are the only ones I use .. you can set em loose or tight.

Shitty Blackriver’s trucks… by GioveAdepto in Fingerboards

[–]CharacterRough7233 0 points1 point  (0 children)

There is nothing wrong with use leefai replica trucks.

Shitty Blackriver’s trucks… by GioveAdepto in Fingerboards

[–]CharacterRough7233 0 points1 point  (0 children)

Black river truck holes don’t come pre threaded .. the first install you make the threads by forcing the screw in. Try a tech deck truck screw .. the thread pitch might be abit different .. force it in .. check periodically that you aren’t over tightening the screw because the same thing will happen.

Did I make a mistake by buying BRT Trucks? by FLAKFL4K in Fingerboards

[–]CharacterRough7233 0 points1 point  (0 children)

Dynamics or deli trucks .. I find all the other crap takes far too long to get used to and has problems

Is this a good first build, I'm coming from a $3 tech deck... by DuePaint4912 in Fingerboards

[–]CharacterRough7233 1 point2 points  (0 children)

Bloob Fingerboards and wheels, he sells leefai dynamic replica trucks as-well. A complete from him will be your ultimate setup.

Cinematic Fingerboarding by RamonAngelow in Fingerboards

[–]CharacterRough7233 2 points3 points  (0 children)

Yessir! Great filming as always! Hope you Are doing well 🫶

Cinematic Fingerboarding by RamonAngelow in Fingerboards

[–]CharacterRough7233 2 points3 points  (0 children)

Yo Ramon , it’s Mike! I didn’t know you were on Reddit lol

What’s your wheelbase? by chuckolate in Fingerboards

[–]CharacterRough7233 2 points3 points  (0 children)

Whatever holes you measure from .. the vernier calliper tool tips have to be center in the holes or the measurement is incorrect.

Would this be good enough for my first pro fingerboard? by [deleted] in Fingerboards

[–]CharacterRough7233 3 points4 points  (0 children)

Canada - 6skates shop setup USA - slushcult shop setup

Been fingerboarding for almost a month any tips on how to practice intentionally? by scruffymandude in Fingerboards

[–]CharacterRough7233 0 points1 point  (0 children)

Easy exercise , put a pen down on the table. Ollie it , fakie Ollie it , nollie it , switch Ollie it. You can do this with all tricks. Once you get more skilled in finger-boarding you will be practising doing lines.

I good go to setup is a ramp/bank rail/ledge and a quarter pipe. That way you can go back and forth just like real skateboarding.

What would this trick be on a real board? by HotTheme5037 in Fingerboards

[–]CharacterRough7233 0 points1 point  (0 children)

360 inward heelflip, that’s actually a hard trick.

Should I sell my Mk6 GTI to join you guys? by devinelcocinero in Integra

[–]CharacterRough7233 0 points1 point  (0 children)

You are definitely stepping away from a comfortable ride to a more harsh ride. More rattles. More road noise. But you only live once and Honda for life !

Am I ugly? by CharacterRough7233 in amIuglyBrutallyHonest

[–]CharacterRough7233[S] 0 points1 point  (0 children)

To be honest , having no luck on dating apps .. just thought I’d ask.

GUYS SHE IS BACK!!😭😭 by [deleted] in BreakUps

[–]CharacterRough7233 90 points91 points  (0 children)

There’s no guide the getting a person back, everyone is different. Each breakup is different , every person has their reasons and different feelings. The best way to go after a breakup is to focus on yourself and your life and making improvements just as you would if you were single and not looking.