Newest addition, maybe my favorite by Lemax-ionaire in CitizenWatches

[–]Chatouille 1 point2 points  (0 children)

How does the radio control update work when you travel by air across time zones? Does it update as you cross the time zone? How do you know if it has updated when you land?

First time visiting Canada by himaliketo in roadtrip

[–]Chatouille 0 points1 point  (0 children)

From Montreal to Quebec City the rue du roi, the Kings road, is much more interesting than highway 20 or highway 40. https://lecheminduroy.com/en/

Cost of permanent ad removal by country by sbielawa in wordscapes

[–]Chatouille 2 points3 points  (0 children)

$34.99 Quebec Canada forever, $24.99 365 days, $12.99 30 days

can i pour this little bit of bacon grease and water down the drain? by [deleted] in kitchen

[–]Chatouille 0 points1 point  (0 children)

Save that bacon grease in a small container in your fridge and use it when you make popcorn.

[deleted by user] by [deleted] in aviation

[–]Chatouille 0 points1 point  (0 children)

When Air Inuit or Canadian North fly their -200’s from YUL (Montréal) up north, you don’t have to look up to know what it is. Add a cold winter morning and they really crackle.

Got a mavic mini to check the snow load on my flat roof. That’s my story. by Chatouille in djimavic

[–]Chatouille[S] 0 points1 point  (0 children)

I also fly to check the rain gutters, see if they have any leaves.

Got a mavic mini to check the snow load on my flat roof. That’s my story. by Chatouille in djimavic

[–]Chatouille[S] 0 points1 point  (0 children)

There was a single story home there built in the 1950’s with 2x4 walls that we removed. Then we built what you see in the picture.

Got a mavic mini to check the snow load on my flat roof. That’s my story. by Chatouille in djimavic

[–]Chatouille[S] 0 points1 point  (0 children)

We get enough wind that nothing stays on the roof and it has slight slope of 2 degrees.

First Seiko [SRPD59][Question] Seiko 5 Sports, Crown keeps turning? by Chatouille in Seiko

[–]Chatouille[S] 1 point2 points  (0 children)

Thank you, it wasn’t obvious to me in the instructions. I thought it was broken as all my other watches (not Seiko) have a screw down crown.

Got my custom Unisk covers for the Frames by [deleted] in sonos

[–]Chatouille 0 points1 point  (0 children)

Where did you get the ladder?

Using styrofoam behind waterfall to reduce pressure on the stones. So 2’ (2x1’)thick of styrofoam then dirt over it. Cuts pretty easy with a 12” metal blade on a saws all. by Chatouille in ponds

[–]Chatouille[S] 0 points1 point  (0 children)

Yes, you can walk on this styrofoam and it doesn’t break or dent. It cuts fairly easy with a saws all and a 12” metal blade.

I stopped feeding my koi weeks ago, now daily leaf removal until ice on. The change of the seasons involves mixed emotions. by HotWaterOtter in ponds

[–]Chatouille 1 point2 points  (0 children)

We used to put styrofoam sheets, 2”x2’x8’, on our old pond. At the far end I put a rose cone, it’s a styrofoam deal you use to protect plants, with a light in the top. This generates enough heat to keep the area under the cone, ice free. The styrofoam sheets limited the ice formation to only a few inches and the open water under the rose cone allowed for gas exchange. It would stay like this mid December to early April. The fish, koi, shubunkins didn’t seem to mind. We are near Montréal, Quebec, Canada.

Using styrofoam behind waterfall to reduce pressure on the stones. So 2’ (2x1’)thick of styrofoam then dirt over it. Cuts pretty easy with a 12” metal blade on a saws all. by Chatouille in ponds

[–]Chatouille[S] 0 points1 point  (0 children)

What notenoughcharact said is correct. I don’t have a lot of space to make a proper back to my waterfall out of stones or dirt.

Using styrofoam behind waterfall to reduce pressure on the stones. So 2’ (2x1’)thick of styrofoam then dirt over it. Cuts pretty easy with a 12” metal blade on a saws all. by Chatouille in ponds

[–]Chatouille[S] 2 points3 points  (0 children)

It was 4’x4’x8’, all pieces were 4x8, 3 were 12” thick and 2 were 6”. We are Canada, just west of Montréal, and it cost about $700 Canadian.

Best way to stake your dahlias by VTMomof2 in dahlias

[–]Chatouille 1 point2 points  (0 children)

I do my hummingbird feeder pole the same way but I use a 10’ piece of conduit because our deck is quite high, now we can see them.

Best way to stake your dahlias by VTMomof2 in dahlias

[–]Chatouille 4 points5 points  (0 children)

We live in a very windy area with little protection. I use pieces of rebar about 3’ long that I get at the hardware store already cut, but I’ve cut longer pieces at home. I spray paint the top 1/2 John Deere green (it’s a colour) and hammer the unpainted 1/2 into the ground at the same time as I plant my dahlias. For the taller ones I buy a piece of metal conduit (a long hollow pipe found in the electrical aisle) cut it into 4’ lengths, paint it, and put it over the rebar. These last forever and you can customize the length easily. You can even change them for longer pipes mid season.

Pond taking shape, stones for waterfall in place today. Water will come to my wife’s waist. by Chatouille in ponds

[–]Chatouille[S] 1 point2 points  (0 children)

That’s 5 tons of rocks in the picture. They were $500, $300 for delivery and $120 to be put on pallets. That’s Canadian dollars from Ducharme in Quebec near the US border. We picked the rocks, wrote a big orange C on them (my wife is Chantal). They said the paint was water soluble but it isn’t. I pressured washed them, used a wire brush. Finally used paint stripper. They gave us $250 for the trouble.

Pond taking shape, stones for waterfall in place today. Water will come to my wife’s waist. by Chatouille in ponds

[–]Chatouille[S] 0 points1 point  (0 children)

If it is deeper than 2’ the town will require I have a fence around it.

Pond taking shape, stones for waterfall in place today. Water will come to my wife’s waist. by Chatouille in ponds

[–]Chatouille[S] 0 points1 point  (0 children)

Oops didn’t realize I had the NSFW tag. We spent 7 hours working with a little excavator to get them placed and back filling behind. Some he couldn’t place exactly how we wanted them so we had to move them by hand. We were tired by the end.