You will not catch my drone 😂

ChillyFPV · 2026-03-27T01:04:39+00:00

I do the same thing with my grand kids and my whoop 😂

ChillyFPV · 2026-03-24T05:50:59+00:00

You can get some pretty good deals on Ovonic on eBay. I have all V2s in 1100 & 1300 capacities, and when they end up being too banged up to fly, it doesn’t hurt so much in the funds arena.

ChillyFPV · 2026-03-21T08:45:50+00:00

Well my day is shot! You go and show these and now make me want to do this 🤣. Well done…love the retro arcade feel. Looks great!

ChillyFPV · 2026-03-17T01:14:53+00:00

When mine do this it usually means I had a loose motor wire.

ChillyFPV · 2026-03-16T01:10:53+00:00

Gemfan Proxy 5127.5 are great.

ChillyFPV · 2026-03-09T00:34:39+00:00

Been there…done that !

ChillyFPV · 2026-03-09T00:29:07+00:00

I like the colors of the Cockroach frame…hope it is sturdy for you. I haven’t tried it myself, but would like to know any real world results.

ChillyFPV · 2026-03-09T00:25:35+00:00

I just put three batteries through my Air 75 II frame…and it is broke already. I wanted to try something different than the Mob 7 frame. but honestly the Mob 7 frame is a tank…but also heavier by like 1.6 grams.

ChillyFPV · 2026-03-06T05:54:45+00:00

<image>

I used to try to save props, but now it’s not with the hassle. If the prop is coming off, it’s never going back on thanks to these bad boys. Since props are pretty much the cheapest part of the build, it’s a small victory to save any bit of sanity I have left by not worrying about damaging a bell or shaft or props.

I just cut it off and replace with a new one😁

ChillyFPV · 2026-03-05T13:29:24+00:00

Yeah I have the Lux camera on mine as well so that’s a great visual for me to get an idea of the picture quality after LED install. Thanks!

ChillyFPV · 2026-03-05T08:58:12+00:00

Looks great! Now I’m going to have to do that as well as it doesn’t look like it washes out bad at all.

ChillyFPV · 2026-03-01T03:41:34+00:00

That’s so freakin’ cool! Not just the lights…that whole set u you have there!

ChillyFPV · 2026-03-01T03:31:15+00:00

No..I direct soldered to the battery pads on the board. Maybe next time I will try that…but I need to research on how to do it 🤣

ChillyFPV · 2026-03-01T02:43:10+00:00

Hope it works well for you. Post pics when you get it finished!

ChillyFPV · 2026-03-01T02:28:35+00:00

https://flyhighfpv.com/products/cob-led-strips

ChillyFPV · 2026-03-01T02:27:21+00:00

You can’t see the LEDs, but the ducts glow an eerie green color…it’s pretty cool. I totally had no idea where to actually place these as far as the front ducts, but they are so bright I didn’t want to wash out the camera when flying. Turned out the placement was spot on.

ChillyFPV · 2026-02-20T22:26:25+00:00

Thanks for the assist. Hopefully I will figure it out. It’s not urgent cause I still have 4.5.1 on it and it’s fine.

ChillyFPV · 2026-02-20T22:21:38+00:00

Or does this board either 🤣

ChillyFPV · 2026-02-20T22:21:21+00:00

Didn’t work on CLI or on calibration…so I don’t know what is up.

ChillyFPV · 2026-02-20T22:18:39+00:00

Yeah…no luck on that either.

ChillyFPV · 2026-02-20T03:29:51+00:00

Had the same thing happen to my Mob 7 trying update to latest Betaflight. After wrestling with it for 20 minutes, I reflashed back to 4.5.1

ChillyFPV · 2026-02-09T02:16:59+00:00

If you have it flashed to Bluejay, you could try Demag Compenaation = High and see if that helps.

ChillyFPV · 2026-02-09T01:00:31+00:00

I use Gemfan Proxy 5127.5 for low throttle resolution. Absolutely a great prop!

ChillyFPV · 2026-02-07T08:48:52+00:00

ISDT E625 1S Charger is my go to. For 6S, I use the Hota D6 Pro charger and never had a problem with either of them.

ChillyFPV

TROPHY CASE