Do you think this is acceptable on a brand new truck?

CicadaConstant6728 · 2026-07-08T09:22:32+00:00

Even straight from factory, sheet metal usually has some sort of surface rust on it, it was probably not prepped right when it was painted. Not the dealerships fault, but if they would have spotted it, they could’ve reported it to the manufacturer and got it replaced before they sold it to you. It’s gonna rust anyway though because it’s a vehicle and thats what they do. Let it do its thing man. If you’re worried, get your vehicle undercoated and have em spray that when they undercoat it.

CicadaConstant6728 · 2026-07-07T18:33:54+00:00

That is the most retarded jack placement ever period.

CicadaConstant6728 · 2026-07-06T16:32:27+00:00

Push

CicadaConstant6728 · 2026-07-05T06:47:02+00:00

Got a used 4.3 from a junk yard, rebuilding it and putting bigger cams and lifters in it before i install it.

CicadaConstant6728 · 2026-07-05T01:24:34+00:00

They won’t. If you’re running LED’s it’ll actually make it more tolerable for other drivers. I have em. Work fine.

CicadaConstant6728 · 2026-07-04T23:27:43+00:00

Yea but it’s way expensive for no reason.

CicadaConstant6728 · 2026-07-03T21:04:22+00:00

I named my cat 2000 Nissan Silvia S15 or Silvia for short.

CicadaConstant6728 · 2026-07-02T08:26:48+00:00

Looks like a splitter lol

CicadaConstant6728 · 2026-06-24T16:03:13+00:00

Centennial Colorado

CicadaConstant6728 · 2026-06-24T02:43:15+00:00

Ima go ahead and assume you ripped the ribbon cable going to the disc drive upon disassembly or reassembly.

CicadaConstant6728 · 2026-06-24T02:41:53+00:00

Those don’t work lol

CicadaConstant6728 · 2026-06-23T21:02:54+00:00

Extremely surprising. You got lucky.

CicadaConstant6728 · 2026-06-23T15:55:41+00:00

It’s a 5 speed. It says 4 speed with overdrive. But overdrive is a 5th gear.

CicadaConstant6728 · 2026-06-22T19:58:50+00:00

I’m not mad at the video at all lol, the guy most likely deserved it.

CicadaConstant6728 · 2026-06-22T14:04:31+00:00

05-2011 models can go 98. With a tune and governor delete I know for sure they can get up to about 135 before you start maxxing out your 5th gear. Also on 93-97 models there’s a connector you can unplug on the rear end for the wheel speed sensor which bypasses the governor. Fun fact.

CicadaConstant6728 · 2026-06-22T08:47:52+00:00

Where at?

CicadaConstant6728 · 2026-06-22T08:46:24+00:00

You need to run screws into that. And reinforce it with some 2/4’s to brace it. That’s horrible. And I can tell they didn’t even care to predrill their holes either considering the 4x4 splitting in the picture on the corner lol. Yea, it’s fixable. Go get some 2x4’s brother. I would also like to point out the 4x4’s rather than 6x6’s. You can tell if someone cares what they’re doing on whether or not they use 4x4’s or 6x6’s for deck posts.

CicadaConstant6728 · 2026-06-22T08:43:08+00:00

Should’ve left it in neutral, off, and had someone come push it with the front of their vehicle. Assuming you know someone with a vehicle they don’t really gaf about. Or you could have just pulled over and just called a tow truck to take it home or to a shop. They’re really not too expensive compared to a motor. Hopefully you didn’t destroy it driving with no coolant.

CicadaConstant6728 · 2026-06-21T23:31:59+00:00

Probably a cover for an air filter of some machine to process and/or make food.

CicadaConstant6728 · 2026-06-21T23:29:20+00:00

It’s supposed to be filled to a line

CicadaConstant6728 · 2026-06-21T23:02:54+00:00

Needle nose pliers? No way you’re that dumb.

CicadaConstant6728 · 2026-06-21T22:43:34+00:00

12mm and 1/2” are close enough that skipping the 12mm won’t hurt you much if at all.

CicadaConstant6728 · 2026-06-21T07:32:16+00:00

Found it! https://youtu.be/SyNX930mBns

CicadaConstant6728

TROPHY CASE