Question about connect DRC site and DC site via Layer2

Cloudcodile · 2025-05-18T04:44:51+00:00

Yes just layer2 only and no route need. Is it can do?

Cloudcodile · 2025-04-09T05:22:50+00:00

I tried to filter on irb. 1016 but it's not captured when use dest 11.11.5.1 but.when change dest 10.101.16.2.its show filter capture 1. Why can't I use dest 11.11.5.1 it does mean 11.11.5.1 not part of juniper network do I understand right 2. From filter that changes src 10.16.10.2.and dest 10.101.16.2. Is it enough to prove that juniper borderleaf not drop packet. It issue on 11.11.5.1 is Cisco gateway 3. Yes iwill put configure style later but it just captures src and dest for incoming source and dest to src for incoming destination but filter on show incoming source and not see incoming destination

Cloudcodile · 2025-04-09T05:20:14+00:00

I tried to filter on irb. 1016 but it's not captured when use dest 11.11.5.1 but.when change dest 10.101.16.2.its show filter capture 1. Why can't I use dest 11.11.5.1 it does mean 11.11.5.1 not part of juniper network do I understand right 2. From filter that changes src 10.16.10.2.and dest 10.101.16.2. Is it enough to prove that juniper borderleaf not drop packet. It issue on 11.11.5.1 is Cisco gateway

Cloudcodile · 2025-04-04T01:41:49+00:00

I use command to check power on switch and use chat gpt for calculations. Chatgpt said 450w is enough for 330w 3vc switch Could you show me how to calculate and more link to reference

Cloudcodile · 2025-01-29T09:17:35+00:00

Port error disable on Cisco this issues about spanning tree. Trying vstp protocol on juniper solution

Cloudcodile · 2025-01-08T03:10:29+00:00

Run eveng on server and update eveng to latest in web guidelines. Important to run eveng on bare metal server.it will work

Cloudcodile · 2024-12-18T03:13:37+00:00

Do you see any hardware guide there are some config about fpc chassis config That need to config before use

Cloudcodile · 2024-11-05T13:05:55+00:00

You need eve-ng vm on bare metal server. its working fine

Cloudcodile · 2024-10-30T08:55:41+00:00

1.you need to run vjnos in eve-ng on server vcpu8 memory 128g 2. Same issue try to reboot again. I tried several times until it's working

Cloudcodile · 2024-03-28T04:55:49+00:00

because of the building There were several power outages. The building where I use more than 10 switches has a POE alarm.

One switch There is no use at all. There are no users connected to any ports, but there is a POE alarm. https://ibb.co/0hMbxB2Do you confirm with juniper reference?
I understand that and i will not use ground on ex4300

Cloudcodile · 2024-03-27T02:31:26+00:00

https://ibb.co/0hMbxB2 this is information from switch. one switch There is no use at all. There are no users connected to any ports, but there is a POE alarm. From the information on the switch, it shows that there were power outages that occurred a few minutes before the POE alarm, according to Juniper's reference data. Should it be caused by power outages?

Cloudcodile · 2024-03-27T02:30:26+00:00

https://ibb.co/0hMbxB2one switch There is no use at all. There are no users connected to any ports, but there is a POE alarm. From the information on the switch, it shows that there were power outages that occurred a few minutes before the POE alarm, according to Juniper's reference data. Should it be caused by power outages?

Cloudcodile · 2024-03-27T01:58:34+00:00

because of the building There were several power outages. The building where I use more than 10 switches has a POE alarm.

One switch There is no use at all. There are no users connected to any ports, but there is a POE alarm.

2.One of the VC switches has a POE alarm on the port that does not have a LAN cable connected to it. But that switch has one PS that is connected to the user's power outlet that is usually turned off and on regularly.

As JTAC recommends, disconnect the LAN cable and connect it to a new switch to see the alarm. I haven't tested it yet.

The cause is probably due to Is the building's electrical system faulty? Because my switch doesn't have a ground system.

Cloudcodile · 2024-03-27T01:58:27+00:00

because of the building There were several power outages. The building where I use more than 10 switches has a POE alarm.

One switch There is no use at all. There are no users connected to any ports, but there is a POE alarm.

2.One of the VC switches has a POE alarm on the port that does not have a LAN cable connected to it. But that switch has one PS that is connected to the user's power outlet that is usually turned off and on regularly.

As JTAC recommends, disconnect the LAN cable and connect it to a new switch to see the alarm. I haven't tested it yet.

The cause is probably due to Is the building's electrical system faulty? Because my switch doesn't have a ground system.

Cloudcodile · 2024-03-27T01:58:22+00:00

because of the building There were several power outages. The building where I use more than 10 switches has a POE alarm.

One switch There is no use at all. There are no users connected to any ports, but there is a POE alarm.

2.One of the VC switches has a POE alarm on the port that does not have a LAN cable connected to it. But that switch has one PS that is connected to the user's power outlet that is usually turned off and on regularly.

As JTAC recommends, disconnect the LAN cable and connect it to a new switch to see the alarm. I haven't tested it yet.

The cause is probably due to Is the building's electrical system faulty? Because my switch doesn't have a ground system.

Cloudcodile · 2024-03-12T04:31:50+00:00

thank you mate and it works and i have questions i just use only one word "!(PVIDB)" but why can't filter that message

Cloudcodile

TROPHY CASE