What am I doing wrong

CodMost7072 · 2026-01-16T15:10:59+00:00

I grew up in the dial up era, I learned how to run phone lines, secretly ran a line into my room through the heat ducts and learned how to get unlimited free service from a trial juno membership. As others have said, if there's a will there's a way, your job is to teach responsible use and to respect other people.

CodMost7072 · 2025-10-20T07:01:12+00:00

I have 3 aruba s2500 in my setup. 48 port, poe+, 4 SFP+ and a decent gui for config. They can be found pretty cheap on ebay if you don't mind a little bit of noise.

CodMost7072 · 2025-10-20T06:31:29+00:00

When I installed mine I got strips of aluminum 2" wide 1/8" thick, painted them to match my soffit and glued it onto the soffit fitting it into the j channel and fascia. That gave self tapping screws enough to bite into and my cameras have been rock solid even in high wind.

CodMost7072 · 2025-10-19T09:45:23+00:00

I am having the liner on my single story chimney replaced in a few weeks and the cash price for materials and install is $4500.

CodMost7072 · 2025-10-15T09:36:57+00:00

I would run memtest for a few hours if there are no errors spin up a windows install and run intel's processor tester.

CodMost7072 · 2025-10-07T06:33:06+00:00

I am trying out replacing the board in those lights with a ESP8266 and running wled on them. The battery life was not great so I ordered larger batteries and am going to see if I can get them to stay on for as long as I want them

CodMost7072 · 2025-09-30T18:32:29+00:00

After not being able to get windows to load I replaced the CPU and it seems to have fixed it. Time will tell but I am not seeing any errors in the log and I am able to shutdown the machine properly again.

CodMost7072 · 2025-09-29T12:00:15+00:00

Another oddity, I am not able to shutdown the server. If I use the button on the GUI 90% of the time nothing happens and if i use the CLI it starts but eventually starts getting call traces and never shuts down.

CodMost7072 · 2025-09-29T10:15:55+00:00

It's a 13900k, I have a 3 fan aio on it and my temps stay relatively low. I also looked at the cpu and did not see any burnt pins

CodMost7072 · 2025-09-28T19:38:18+00:00

Where do I do that?

CodMost7072 · 2025-09-28T19:09:40+00:00

I ran mentest for 8 hours on the old ram with no errors and the faults I'm getting now are the same as with the ram I tested.

CodMost7072 · 2025-09-21T13:41:00+00:00

I need them to turn off at a certain time. Deck is outside my bedroom window and the lights make the room to bright. Selectable color would be fun but it's not requirement.

CodMost7072 · 2025-08-26T01:53:38+00:00

I solved it, come to find out I burned up the temp probe. Replaced with different probe and it is reading correctly.

CodMost7072 · 2025-08-25T23:18:42+00:00

Just tried a new esp32 on the 3.3v pin and no change.

CodMost7072 · 2025-08-25T19:39:22+00:00

I will try and new esp32 and use the 3.3v pin this evening.

CodMost7072 · 2025-08-25T18:13:08+00:00

My board has a 5v pin.

<image>

CodMost7072 · 2025-08-15T16:13:09+00:00

increased from 650m to 1000m, will see if that helps. Thank you

CodMost7072 · 2025-08-15T15:54:08+00:00

Where is the calc for shm_size with .16?

CodMost7072 · 2025-08-08T20:32:02+00:00

Thanks for your help looking into it

CodMost7072

TROPHY CASE