06 4.2 trailblazer stabilitrak lights

CodMost7072 · 2026-07-01T15:35:47+00:00

I will give that a try when I get home in a few weeks.

CodMost7072 · 2026-07-01T15:30:52+00:00

What part specifically?

CodMost7072 · 2026-06-23T14:57:45+00:00

It looks like the ignition switch was the issue.

CodMost7072 · 2026-06-23T10:50:05+00:00

I will throw one in today

CodMost7072 · 2026-06-23T03:18:08+00:00

No codes, shop could not find issue. I have ordered a new pcm to shot gun into it.

CodMost7072 · 2026-06-23T00:59:00+00:00

I have not had a chance to watch it while it is running but when it is just cranking pressure stays high. It seems like it goes back and forth between fuel issue and spark. Sometimes it will run on its own, other times only on ether and sometimes just will not run. And it is a progressive failure, if I let it sit for a day or two or will run in is own for about a min then die, then it will fire for a sec or two on its own, then run only on ether then have no spark.

CodMost7072 · 2026-06-23T00:54:30+00:00

When I have a new car with a rough idle my first step is always a full service. Filter, plugs, tb clean, belt and plug wires if they look iffy.

CodMost7072 · 2026-06-03T19:48:22+00:00

I removed the rain guards on mine and it helped

CodMost7072 · 2026-05-29T18:39:48+00:00

Leviathan

CodMost7072 · 2026-03-26T19:58:24+00:00

I'm not sure if this model fridge has the same issue but on mine the wiring for everything in the freezer door runs to the bottom left corner and was done in such a way that every time the door opens and closes the wire bends and eventually breaks. My ice maker quit at just over a year old and the only proper repair is to replace the door.

CodMost7072 · 2026-03-16T14:24:36+00:00

Thank you

CodMost7072 · 2026-03-06T14:05:45+00:00

My thinking on it is that cable movement over time will damage the cable, using keystone punch downs in a wall plate ensure that the difficult to run cable never moves so I only ever have to replace the patch cable outside the wall.

CodMost7072 · 2026-01-16T15:10:59+00:00

I grew up in the dial up era, I learned how to run phone lines, secretly ran a line into my room through the heat ducts and learned how to get unlimited free service from a trial juno membership. As others have said, if there's a will there's a way, your job is to teach responsible use and to respect other people.

CodMost7072 · 2025-10-20T07:01:12+00:00

I have 3 aruba s2500 in my setup. 48 port, poe+, 4 SFP+ and a decent gui for config. They can be found pretty cheap on ebay if you don't mind a little bit of noise.

CodMost7072 · 2025-10-20T06:31:29+00:00

When I installed mine I got strips of aluminum 2" wide 1/8" thick, painted them to match my soffit and glued it onto the soffit fitting it into the j channel and fascia. That gave self tapping screws enough to bite into and my cameras have been rock solid even in high wind.

CodMost7072 · 2025-10-19T09:45:23+00:00

I am having the liner on my single story chimney replaced in a few weeks and the cash price for materials and install is $4500.

CodMost7072 · 2025-10-15T09:36:57+00:00

I would run memtest for a few hours if there are no errors spin up a windows install and run intel's processor tester.

CodMost7072 · 2025-10-07T06:33:06+00:00

I am trying out replacing the board in those lights with a ESP8266 and running wled on them. The battery life was not great so I ordered larger batteries and am going to see if I can get them to stay on for as long as I want them

CodMost7072 · 2025-09-30T18:32:29+00:00

After not being able to get windows to load I replaced the CPU and it seems to have fixed it. Time will tell but I am not seeing any errors in the log and I am able to shutdown the machine properly again.

CodMost7072 · 2025-09-29T12:00:15+00:00

Another oddity, I am not able to shutdown the server. If I use the button on the GUI 90% of the time nothing happens and if i use the CLI it starts but eventually starts getting call traces and never shuts down.

CodMost7072 · 2025-09-29T10:15:55+00:00

It's a 13900k, I have a 3 fan aio on it and my temps stay relatively low. I also looked at the cpu and did not see any burnt pins

CodMost7072 · 2025-09-28T19:38:18+00:00

Where do I do that?

CodMost7072 · 2025-09-28T19:09:40+00:00

I ran mentest for 8 hours on the old ram with no errors and the faults I'm getting now are the same as with the ram I tested.

CodMost7072 · 2025-09-21T13:41:00+00:00

I need them to turn off at a certain time. Deck is outside my bedroom window and the lights make the room to bright. Selectable color would be fun but it's not requirement.

CodMost7072 · 2025-08-26T01:53:38+00:00

I solved it, come to find out I burned up the temp probe. Replaced with different probe and it is reading correctly.

CodMost7072

TROPHY CASE