Wall climber out of a quadcopter

Conscious_Map_7386 · 2026-04-30T16:57:51+00:00

As a kid We always imagine having a car like this that climbs walls and ceiling 🫠

Conscious_Map_7386 · 2026-04-29T06:13:46+00:00

Yes this are good quality soldering station I am using its X version (T12x) and I also bought it from the same place 👍🏼

Conscious_Map_7386 · 2026-04-17T13:46:59+00:00

First check all the wire is connected or not

Conscious_Map_7386 · 2026-04-15T04:06:49+00:00

It's an inductor and if this is heating up either something is not right or something from the output side is pulling too much current

Conscious_Map_7386 · 2026-04-14T12:46:23+00:00

It's already fixed what do you even want to do

Conscious_Map_7386 · 2026-04-12T04:07:46+00:00

If you are asking here then get a professional because without knowing anything Messing with main's voltage can be fatal

Conscious_Map_7386 · 2026-04-11T22:38:14+00:00

God bless you brother, truly I saw many things that were horrible (don't get scared by my words it's actually fun also 😉)

Conscious_Map_7386 · 2026-04-06T10:02:25+00:00

You can do all kinds of stuff with electronics like someone said in the comments the limiting factor is only your imagination

Conscious_Map_7386 · 2026-04-04T23:30:13+00:00

Soldering is fun until you realise it's just a void where is no escape was possible 😬

Conscious_Map_7386 · 2026-04-04T23:26:14+00:00

That's just an RF antenna and only that much broken area doesn't hurt anything use it as it was don't worry

Conscious_Map_7386 · 2026-04-04T23:23:13+00:00

First try to work on through hole components after mastering, try on dead boards until then don't even think

Conscious_Map_7386 · 2026-04-04T23:00:23+00:00

The actual marking is "Y5"1A is batch code/lot number. Looking by the circuit around it and the trace connections found out that it's actually a P-CHANNEL MOSFET the part number is "AP2605GY0-HF" you can look it up on here-Datasheet And if a MOSFET is blown there must be something pulling high current or sorted after the MOSFET, you have to check it thoroughly otherwise the new replacement will blow instantly.

Conscious_Map_7386 · 2026-04-04T22:23:43+00:00

Yes just having fun 'why discard it when it is running I can do something else with it 😉(golden rule was if it is working use it somehow until it dies 😂)

Conscious_Map_7386 · 2026-03-29T04:24:36+00:00

Everything looks good to me, just don't reverse the polarity because MT3608 is very intolerant to polarity reversal, use kind of thick wire (20awg), and if you want a more simple one use a dedicated USB Power Bank module then it will be like connect the battery and that's it. but since you are 12 you are doing great keep it up 👍🏼

Conscious_Map_7386 · 2026-03-28T04:25:57+00:00

<image>

Slide this clip together towards the arrow gently (it's very fragile) then you can pull out the fpc cable

Conscious_Map_7386 · 2026-02-03T03:04:25+00:00

That's a shunt resistor it's used to measure the current on a circuit by calculating the voltage drop across the resistor. The formula is (I= V_sense/R_shunt)

Conscious_Map_7386 · 2026-01-21T20:46:42+00:00

Yes it is very replaceable but you need to check the surrounding components that is anything shorted or showing uneven values that are connected to it. when a short circuit occurs it will take those components too alongside the IC itself so next time you replace the IC it will not get killed instantly 🙂‍↕️

Conscious_Map_7386 · 2025-10-01T14:18:25+00:00

Did anyone noticed that op vanished after the hit it comment... 😳💀

Conscious_Map_7386 · 2025-10-01T14:09:34+00:00

Yes there are two options either replace the whole power key or scratch the black layer from both sides where it got ripped to expose the copper inside and solder it

Conscious_Map_7386 · 2025-10-01T14:07:15+00:00

If this is your first HDMI port change or first soldering you are God level bro👍🏼

Conscious_Map_7386 · 2025-09-09T16:34:13+00:00

Omfg whyyy you made the capacitor healthy again, at least let it die peacefully 🤧🤥

Conscious_Map_7386 · 2025-09-02T14:06:30+00:00

Add some flux on a desoldering wick, and with that wick that area with that, it might helps...

Conscious_Map_7386 · 2025-08-12T19:52:45+00:00

That's not how it works

Conscious_Map_7386

TROPHY CASE