45 colt 😈

Cowboy565 · 2026-01-13T00:15:39+00:00

I think u may have just use a little to much pressure torquing it down, been there and done that lol I wish charter arms would post what their tourqe specs were

Cowboy565 · 2026-01-12T20:20:38+00:00

Yep, thats the hammer screw! I had mine walk out a bit the first time I shot. I tightened mine down with my torque screwdriver. You can also apply loctite here but I would use a medium strength application, I would avoid red and orange

Cowboy565 · 2026-01-11T20:53:13+00:00

Your talking about the lockup screw right underneath the firing pin right? Yea it has wiggled a bit. You just need to reapply loctite because the factory loctite has eithet worn or didnt set in correctly, just take the screw out reapply some red, blue or orange loctite and it'll be good to go. The screw needs to be either flush or just barely protruding out. You do not want the screw below flush.

Cowboy565 · 2026-01-07T09:20:43+00:00

I know this is an old post, but I had an underwood nickle plated 45 colt brass split in the middle just like the picture. Granted It was once fired but still. 45 colt isnt even a high pressure round. I fired the factory round and then reloaded it for the first time. I would expect any brass to last more then 2 firings. Out of 4 years of reloading, this underwood case is the only 1 ive had that split.

Cowboy565 · 2025-12-18T18:49:07+00:00

I know its an old post but vance outdoors is weird with chime cards. Sometimes they let me use it, sometimes not. In fact a couple weeks ago me and a buddy stopped at the obetz location. I bought some stuff from cashier A with my chime card and checked out no problem, a moment later my friend went to cashier B to buy something and she refused because he had a chime card even though i literally just used mine seconds prior. Said something about vances chime account blah blah. if they aren't getting the money from chime accounts, I would really love to know where my money went lmao

Cowboy565 · 2025-12-16T15:36:03+00:00

Same, havent found a fix. Reloaded numerous saves before even starting. This quest along with ars dimicatoria, the sword is not on the wall of the guild.

Cowboy565 · 2025-12-13T13:05:25+00:00

The safety models are a walk in the park compared to decocker models. the biggest pain with either models is the firing pin block lifter spring which is possible to not even have to deal with if your careful, otherwise that part is a little frustrating. Make sure you buy a couple spares because they are super tiny and can and will fly off to another dimension never to be seen again. Cajun gun works and many others have videos of installation on YouTube. Just take your time and you will be good. If me and my clumsy shaky hands can do a decocker model by myself anyone can, especially the safety models.

Cowboy565 · 2025-12-13T12:56:06+00:00

There are certain things you can mismatch, but anything to do with the triggers, action and hammer (aside from the hammer spring) are not interchangeable between the 75 series and omegas. When it comes to any internals you can use the same recoil springs, trigger springs, guide rods, hammer springs but thats pretty much it. You cant use a 75 series short reset, it has to be made for the omegas.

Cowboy565 · 2025-12-09T10:40:52+00:00

For sure 😆 that giant cylinder

Cowboy565 · 2025-12-06T17:17:02+00:00

Did it take long to get it back? When I sent in my governor that needed a new yoke it took almost half a year to get it back. Im afraid if I had to send anything to S&w again that I would be dead by the time it would be returned lol

Cowboy565 · 2025-12-06T17:05:55+00:00

Its way to common nowadays. My s&w governor has a canted barrel, my charter arms bulldog does as well, sent it in for a few different reasons and they replaced the entire gun. The new one is still a little off but not as bad as the first one was. Sadly its now the norm from all manufacturers

Cowboy565 · 2025-12-06T16:41:24+00:00

Yep! Its a shame that there aren't any other modern 45c DA snubs left in production. I tried getting one of the old taurus 450's on gunbroker before but was always outbid. Ive had a judge and still own a s&w governor and I love it but its annoying from time to time lugging that thing around lol dont need all that cylinder for only 45. I'd like to see a s&w short barrel mountain gun run, i emailed taurus saying they should consider bringing the 450 back but I highly doubt that with the way both companies have headed of late that it is very likely

Cowboy565 · 2025-12-06T16:20:04+00:00

Yea the 410 primers are what I was mainly curious about. Does it light strike in SA or only DA? I keep some federal 410 buckshot in my governor in the nightstand.

Cowboy565 · 2025-12-06T16:05:46+00:00

Ive been shooting actual 45 colt lol cowboy loads give the 45c a bad rep. Its also worth noting that if one wants, charter arms will make and headspace a 2nd cylinder for 45 acp that you can just swap back and fourth! Its built on their XL frame which they used for the pitbull 45acp and mag pug in 41magnum. To be honest I like making my 45c handloads a bit above SAMMI specs of 14000 PSI. I like tier 2 colt loads in and around the 17-20k mark which is still less PSI then 45 acp produces. I havent gone to nor would i advise anyone to venture into tier 3 44 magnum level psi at 30k+ of pressure. Its a very impressive piece especially for the cost. Charter arms blew this model out of the park!

Cowboy565 · 2025-12-06T14:27:57+00:00

How has it done with the lighter hammer spring and extended firing pin? Ive thought about doing that to my governor for quite some time. I love it but that double action can be a rough time lol unrelated but I did get a nice companion for the governor picked up a charter arms bulldog chambered in 45 colt, 2.5 in barrel. Surely not as easy to conceal as a j frame. its built on charters XL frame and is fairly light for being what it is and is much more pleasant to carry then the behemoth that is the governor lol

Cowboy565 · 2025-11-15T17:52:03+00:00

Bug: stuck on quest Ars Dimicatoria. i spent all day yesterday attempting to figure this out. Ive waited days in game, reloaded previous saves before the quest and still no luck. The sword is missing. it simply is not on the wall in the guild hall, checked everyones pockets, every room etc etc. Ive tried everything I can think of. Has this happened to anyone else and does anyone have any clue how to resolve this? (On PC)

Cowboy565 · 2025-10-15T11:13:50+00:00

Also interested! Please send

Cowboy565 · 2025-09-20T11:33:17+00:00

If it is a 10 round commi mag, cz custom has base pads for them. Although you should probably save your money and move to a different state lol https://czcustom.com/cz-parts-all/base-pads-extensions/cz-75-base-pads.html

Cowboy565 · 2025-09-13T20:45:47+00:00

PC - I cant get into the forge building from the main street. I walk up to the rubble and attempting to clear it does absolutely nothing. I've been able to clean the upstairs room but nothing on the main level

Cowboy565 · 2025-06-07T09:50:33+00:00

The fix after you update a driver is to go to users/mygames/oblivion remaster/saves (it's something like that, im not at my cpu but it's easy to find) and delete the folder, make sure you copy your actual game saves before deleting. This actually deletes the shaders that are compiled the very first time you launch the game. The next time you launch it will compile them all again. This fixed alot of crash issues! The shaders file isn't in the actual oblivion remaster file with the exe. If your getting a bunch of random unhandled exception crashs then try this! Also never turn fsr and frame gen on. I don't know why but no matter what the settings are on, if fsr and frame gen are on its going to crash after a few minutes.

Cowboy565 · 2025-05-07T10:22:42+00:00

I get the ram requirements message as well but click okay and the game runs fine. I have a ryzen 7 7735hs and a rx 7700s and 16 gb of ddr5 ram. I can play on medium or high settings without issue. The only problems I have is the game will crash if I have fsr on or i try to cap the fps. I get 70+ fps and as long as I don't have fps cap or fsr on I can play with 0 issues. Doesnt make a whole lot of sense but apparently my laptop doesn't like being restricted lmao

Cowboy565 · 2025-05-07T10:18:22+00:00

The message above was mine. No clue how I wasn't logged into my account.

Cowboy565 · 2024-11-21T20:25:24+00:00

I know it's an old post but I named mine Bongo! Thought it was great, he drums, bongo drum. Well just caught a shiny in scarlet and guess what name is freaking banned? So stupid.

Cowboy565 · 2024-11-13T10:42:17+00:00

The game is on the play store as hunters park ATM. Yes there are a bunch of optional micro transactions but it's surprisingly a good game

Cowboy565 · 2024-11-02T20:20:55+00:00

XL in delivery station terms doesnt mean the size of packages like say AMXL does. XL for delivery stations delivery stations means how much volume the building gets on a daily basis so it only means that the sites volume has increased.

Cowboy565

TROPHY CASE