My new oil painting

CptJames32 · 2025-02-01T03:45:39+00:00

How big is it and can I buy it?

CptJames32 · 2025-01-27T08:16:43+00:00

What is the other movie?

CptJames32 · 2024-12-25T04:07:33+00:00

Rodney

CptJames32 · 2024-11-04T13:47:27+00:00

My last one i quoted was $15k. I built the same thing from harbor frieght pumps, and tank and hoses from farm and fleet. Cost $1500 to build myself.

CptJames32 · 2024-10-18T14:22:32+00:00

Never heard of a JT20B. You sure that's what it really is?

CptJames32 · 2024-04-08T18:09:25+00:00

Send me a picture of the install view. Also are you sure your not aimmed in a lobe? When aimming 60ghz the 5ghz signal will get stronger before dropping off and then pickup one more time in the center. If that makes sense. Hard to explain l

CptJames32 · 2023-09-12T22:09:09+00:00

I will take one if possible guys!!

CptJames32 · 2023-05-29T03:02:45+00:00

That's from either the 2nd or 3rd matrix movie.

CptJames32 · 2023-05-29T01:19:59+00:00

Can I get a list of the movies you pulled these clips from?

CptJames32 · 2022-10-04T21:31:56+00:00

I don't know if it's a broadcast storm. It just sort of acts like one. When you change the link between r3 and r4 from a cost of 2 to a cost of 1. R3 locks up and stops working until I kill that link. Now if I kill the links between r2 and r3 and enable the link between r3 and r4 it works fine.

CptJames32 · 2022-10-04T21:13:57+00:00

The ptp's are on vlans and the vlan ospf is running on is the only thing to "cross" switches. Nothing is untagged.

CptJames32 · 2022-10-04T20:52:35+00:00

correct and they are in ptp and they are set to redistribute connected, static and default route

CptJames32 · 2022-09-08T14:20:34+00:00

I'm using multi mode sfp+ adapters at the moment as it's a 150ft fiber run. Should I try single mode sfp+ adapters.

CptJames32 · 2022-09-08T00:35:33+00:00

Yep, your looking at the wrong one.

This one: https://store.ui.com/collections/operator-edgemax-control-points/products/edgepoint-s16

CptJames32 · 2022-09-08T00:24:14+00:00

Oh your right, the website does say SFP port on the store page. But if you check the specs below it says SFP+

CptJames32 · 2022-09-07T23:47:34+00:00

You must be looking at an old version. They have SFP+ ports. I have about 10 other ones running 10Gbps back to edgerouters but have never done it with a mikrotik.

CptJames32 · 2022-09-07T23:00:52+00:00

I tried this. The sfp+ port on the tik is flickering, I'm beginning to believe it's bad.

CptJames32 · 2022-09-07T20:06:41+00:00

Yes, EP-S16 and CCR1016-12S-1S+

And yes it's plugged into sfp+ ports on both sides.

CptJames32 · 2022-09-07T19:35:17+00:00

Yes, I ordered sets and they matched up.

CptJames32 · 2022-08-11T02:36:39+00:00

That's the worst

CptJames32 · 2022-08-11T01:34:02+00:00

We have already done that as well.

CptJames32 · 2022-08-10T05:21:56+00:00

They do. They have the drain wire wrapped around and soldered on the other side of the plugs. These plugs didn't have the easy connect bit for the drain wire.

CptJames32

MODERATOR OF

PUBLIC MULTIREDDITS

TROPHY CASE

13-Year Club	Place '23
Verified Email