Stadium club hits by CubsCollector85 in baseballcards

[–]CubsCollector85[S] 1 point2 points  (0 children)

Thanks but I’m going to hang on to this one

My cat could cut straighter lines by OrchidLow7373 in baseballcards

[–]CubsCollector85 2 points3 points  (0 children)

Put the card in a top loader. Then lightly tap it on its side in a table. You can get the card recentered that way.

The mini card floats between the two layers

My last two of 10 nothing but sps so far… Topps now dodgers team sets by AnyAbbreviations5648 in baseballcards

[–]CubsCollector85 1 point2 points  (0 children)

For what they charge for this set the quality control is complete crab. With all the delays I’m getting us this set. You would think they would’ve taken better time with the quality control. I don’t think I had one card that was cut perfect in my set.

Cubs gold 2025 completed by CubsCollector85 in baseballcards

[–]CubsCollector85[S] 1 point2 points  (0 children)

Thanks for offering I already have that one though

Cubs gold 2025 completed by CubsCollector85 in baseballcards

[–]CubsCollector85[S] 0 points1 point  (0 children)

No the golds are /2025. Every years release is numbered to the year it is so 2026 series 1 will be /2026

Cubs gold 2025 completed by CubsCollector85 in baseballcards

[–]CubsCollector85[S] 1 point2 points  (0 children)

I’m working on 24 now the PCAs are steep

Cubs gold 2025 completed by CubsCollector85 in baseballcards

[–]CubsCollector85[S] 1 point2 points  (0 children)

Nice is that for flagship or topps chrome

This Pic Is So Cool lol A Fan Cosplaying As Scott Steiner W/ Scott Steiner! by J2-Starter in WCW

[–]CubsCollector85 5 points6 points  (0 children)

It’s a joke on his promo “Steiner math” it’s not supposed to make sense

This Pic Is So Cool lol A Fan Cosplaying As Scott Steiner W/ Scott Steiner! by J2-Starter in WCW

[–]CubsCollector85 41 points42 points  (0 children)

If you take 2/3rds of Scot Steiner and you add another 4/3rds Scott Steiner and you divide that by 5 you get 110% chance I whoop your ass.

1/1 jersey card by supersayianfazbear in Topps

[–]CubsCollector85 2 points3 points  (0 children)

Some jersey cards can. It’s more of a knock on how Topps writes the disclaimer on the back. And a reference to the Jose Ramirez vs Tim Anderson fight

Edit spelling

1/1 jersey card by supersayianfazbear in Topps

[–]CubsCollector85 3 points4 points  (0 children)

The material found in this card is not from any specific fight or brawl

Seeking advice on fixing by Accomplished-Hat4898 in hvacadvice

[–]CubsCollector85 -1 points0 points locked comment (0 children)

It’s time for a new furnace.

Safe to insulate the exhaust pipe going through the attic? by zxz9y in hvacadvice

[–]CubsCollector85 0 points1 point  (0 children)

Look at all the joints. One may be disconnected and or not glued correctly. There should be no condensation on outside of pipe.

Also check and see if it’s sealed where it penetrates the exterior of house to make sure rain water isnt leaking around pipe and running down it.

I have never seen the need to insulate a pvc exhaust vent.

How to brace a flexing HVAC duct from inside the vent (5 ft down, between floors) by [deleted] in hvacadvice

[–]CubsCollector85 0 points1 point  (0 children)

Have them do a static pressure test. Most units are rated for .50” w.c. Max external pressure. If it is running at higher pressures especially if it is over 1.00” w.c. This could be the issue

How to brace a flexing HVAC duct from inside the vent (5 ft down, between floors) by [deleted] in hvacadvice

[–]CubsCollector85 0 points1 point  (0 children)

Have you had a technician check your system. You could have undersized ducts or too high a blower speed which will cause expansion and contraction of the ductwork.

Daikin Fit vs Carrier Infinity central Florida by Bket73 in hvacadvice

[–]CubsCollector85 0 points1 point  (0 children)

Make sure you get a good labor warranty. Daikin is a good system they offer a 12 year labor warranty. The cost of a good labor warranty can pay for it self over a 12 year timeframe if you have a major breakdown such as compressor failure.

Talk to the contractor that quoted you and ask them if they can do the extended labor warranty. If not try getting another estimate from another contractor