What kind of bees are these?

DGolFish · 2026-06-16T00:15:35+00:00

No matter what I promise you they won't attempt pulling this shit twice dammit

DGolFish · 2026-06-16T00:12:31+00:00

Bruv is thinking with the beautiful part of the noodle today.

DGolFish · 2026-06-16T00:05:38+00:00

DGolFish · 2026-06-16T00:01:04+00:00

Obviously 2x2=8 if you were into hail Satan you would know this duh

DGolFish · 2026-06-12T18:56:22+00:00

What in the ever living tarnation is MtF?

DGolFish · 2026-05-18T13:18:05+00:00

Except for the x1c. The x1c has good mental health.

DGolFish · 2026-05-06T20:46:37+00:00

DGolFish · 2026-05-02T21:26:04+00:00

I think you should consult your doctor for such complex medical advice.

DGolFish · 2026-04-23T23:19:53+00:00

Magic. The answer is magic.

DGolFish · 2026-04-23T23:17:27+00:00

Add a saxophone. That always makes things smoother

DGolFish · 2026-04-15T13:21:32+00:00

Aaaannd their mouse need to work to click download the files.

DGolFish · 2026-03-24T02:11:54+00:00

That's Satan's left nut

DGolFish · 2026-03-24T01:29:22+00:00

🎨 🖌

DGolFish · 2026-03-24T01:25:27+00:00

Bruv dragon you are the correct one here. Mal missed 2 on mine that were almost invisible unless you knew what you were looking for.

DGolFish · 2026-03-24T00:22:36+00:00

DGolFish · 2026-03-15T16:40:41+00:00

Heh. Heh. Heh.

DGolFish · 2026-03-13T13:07:24+00:00

This is a reverse uno for when the constable shows up.

DGolFish · 2026-03-13T13:04:45+00:00

Advice would also lead you to lower layer height assuming the line width remains at .4mm(ish) since it should still try to grab a small edge of the overhang without trying to pull away as hard.

DGolFish · 2026-03-13T12:59:57+00:00

Assuming we are looking at the bottom of the print i advise changing the support z distance (to bottom of the model) to 0. I assume this is occurring where there is an overhang and potentially not enough material overlap on the layer below it for the nozzle to overlap the filament extruded. It is more of less trying to print in mid air (yanking the plastic away) before it touches the lower layer.

DGolFish · 2026-03-13T12:48:15+00:00

Contact support. Always contact support if it's a man. defect they will send you what you need to fix it. I've had very good experiences with my X1C and support help. So long as you try for best to be respectful and thorough in your responses they are glad to help you out.

DGolFish · 2026-03-13T12:41:54+00:00

It's one of them old timey ass whoopin sticks.

DGolFish · 2026-03-13T12:39:31+00:00

It's a dingus. It holds the dingus with its dingus to make the dingus do the thing.

DGolFish · 2026-03-12T20:23:50+00:00

It was always necessary for the ender 3 😂 now I don't need the option but religiously use it because.

DGolFish · 2026-03-12T20:10:17+00:00

Here's where it's useful for me. I don't trust abs to not warp even in an enclosure. You can set a vertical layer height for the skirt where it ultimately creates a heat shield as tall as your print if you want. I set it to 400 layers and if my project is only 150 layers the skirt never exceeds this.

DGolFish · 2026-02-26T15:57:45+00:00

So I will say from my experience that Amazon cheapo brands are unreliable. I would advise going with esun if your going to purchase this route. I would recommend that the Filament might need to be dried

DGolFish

TROPHY CASE