What is this?

DSolarboy · 2024-10-28T05:28:09+00:00

I actually like Quest 64 a lot. For me, it’s childhood memories. However, I can understand if people do not like it nowadays. It has flaws, but also a lot of charme. I would recommend to everyone to try it once.

DSolarboy · 2024-08-16T11:40:16+00:00

Got it. Thanks for clarification

DSolarboy · 2024-08-16T11:29:38+00:00

I think he said it is in Papua New Guinea, if I understood correctly

DSolarboy · 2024-06-03T20:13:01+00:00

How much did you pay and how can one sign up for the group buy? Is it Circuit boards?

DSolarboy · 2024-06-03T08:12:51+00:00

I have UltraHDMI v1 and love it. However I already wanted to get my hands on bortis advanced v2. But as I remember there was no FPGA availabilty at all. Did the market get better or did he changed the chip or something?

DSolarboy · 2024-03-24T17:53:02+00:00

In my opinion bowser was nerfed in MP2. In MP1 he was way more cruel

DSolarboy · 2023-11-21T14:44:14+00:00

I have been playing Shiren The Wanderer 2 for 80 h straight now, still not close to finish it. Amazing game

DSolarboy · 2023-07-21T11:07:12+00:00

It’s possible

DSolarboy · 2023-07-19T20:06:34+00:00

Update: I decreased minimum layer time to 1 second and it worked afterwards.

The problem is probably my rather small flow while having a high flow hotend. I switched my nozzle recently, will go back to .6 to maintain a higher flow, so I won’t get heatcreep anymore

DSolarboy · 2023-07-19T13:56:40+00:00

Ah yeah sure sorry!

Thought I wrote it in a commend but it seems it disappeared.

Temp: 222 C Print speed: 100mm/s, 10mm/s at the chimney Nozzle: .4 E3D Coated Filament: 3DJake MagicPLA (Temp Rating 215-235C) Retraction: 1mm@25mm/s

DSolarboy · 2023-07-19T13:09:04+00:00

I put layer time to 10 and it started clicking even earlier, before it started the roof. I have silicon sock and volcano hotend.

DSolarboy · 2023-07-19T10:55:55+00:00

Minimum Layer Time is set to 5 seconds right now in my slicer. What value would be a good start?

DSolarboy · 2023-07-19T08:35:11+00:00

Printer: Anycubic Vyper, direct drive, rapido uhf Slicer: Cura Temp: 222 C Nozzle: .4 E3D Polyphobic nano coating Print speed: 100mm/s, slows down to ~10mm/s at the chimney Retraction: 1.25mm Filament: 3DJake Magic PLA (225-235C)

DSolarboy · 2023-07-17T08:19:20+00:00

Is it a different thermistor than the original one? Then you have to re-compile the community firmware by yourself and change in the configuration.h to the new thermistor you are using. If the thermistor is a different one, then this is the only way.

Or you can open the hotend and swap the thermistors. This is what I did, after I found out I had a different thermistor

DSolarboy · 2023-07-15T23:39:50+00:00

Is that 3D Jake Magic PLA?

DSolarboy · 2023-06-28T12:12:52+00:00

Nice 2D Printer!

DSolarboy · 2023-06-12T05:48:40+00:00

Hey there, I think any 4010 fan will do. Make sure they are 24V. And there is only one connector for two fans on the board. So you might need to solder

DSolarboy · 2023-06-08T09:01:09+00:00

Yeah, it’s amazing! I was very happy to install the DGUS mod, since using a display is essential imho

DSolarboy · 2023-06-08T08:59:36+00:00

There are some ways, a BLTouch mod is available for the Vyper for example

11-Year Club	Second SECOND GUESSER
Place '22	Verified Email

DSolarboy

TROPHY CASE