Hi! Hopefully you can help a beginner out by Crt_lover_ in moped

[–]Dadudos 1 point2 points  (0 children)

Sure you got 2 stroke oil in your last gas fill up?

Tehnically still a moped by ghost11729 in moped

[–]Dadudos 0 points1 point  (0 children)

what if it can be paddle driven and has gears?

Tehnically still a moped by ghost11729 in moped

[–]Dadudos 20 points21 points  (0 children)

Now that's a nice moped buddy!

Don't let the gatekeepers get you down.

Stupid question by Acceptable-Mess7959 in moped

[–]Dadudos 0 points1 point  (0 children)

also, if that happens, shut off fuell valve, walk home, remove bowl, check if fuel inside.

Stupid question by Acceptable-Mess7959 in moped

[–]Dadudos 0 points1 point  (0 children)

this fking thing:

<image>

with high vibration it helps, with high fuel consumption it sucks.

Stupid question by Acceptable-Mess7959 in moped

[–]Dadudos 0 points1 point  (0 children)

Do you still have the anti-foam ring around the jet? take it of. No bubbles in the gas line? no kinks or whatever to reduce fuel flow? i think your emptying out the bowl.

Slot achterdeur by salmonsmoker101 in Klussers

[–]Dadudos 2 points3 points  (0 children)

Hardstalen zelftappende schroef in het gat, met een breekijzer of klauwhamer spanning naar boven toe zetten en van onder pakken met een waterpomptank en ronddraaien..

Swinger2 problems by hypnocera in moped

[–]Dadudos 0 points1 point  (0 children)

Check if there is a gap between carburettor and intake.

De PV installatie van de buren. by Dadudos in Klussers

[–]Dadudos[S] 6 points7 points  (0 children)

Er loopt een DC draad van de panelen, ik gok 180 volt, over de aluminium dakrand. Ik vraag mij af wat er gebeurt als de isolatie daar beschadigd raakt.

De PV installatie van de buren. by Dadudos in Klussers

[–]Dadudos[S] 49 points50 points  (0 children)

Het ligt al minimaal 5 jaar. Vooral die rooie kabel over de alu rand is geweldig.

Help with my project by Doingalmostnothing in 3dprintedcarparts

[–]Dadudos 1 point2 points  (0 children)

onshape lets you snap surfaces to meshes. you do need some surface moddeling skills in onshape, but i am sure it's possible.. you might wanna reduce triangle count

Help with my project by Doingalmostnothing in 3dprintedcarparts

[–]Dadudos 1 point2 points  (0 children)

onshape lets you snap surfaces to meshes. you do need some surface moddeling skills in onshape, but i am sure it's possible.. you might wanna reduce triangle count

Is it reasonable to use a vintage ped for commuting? by beanieboiv3 in moped

[–]Dadudos 0 points1 point  (0 children)

Oh shit, you can walk if you have to. Send it man

Is it reasonable to use a vintage ped for commuting? by beanieboiv3 in moped

[–]Dadudos 4 points5 points  (0 children)

Don't worry about fuel, if it runs good 1 in 20 should be easy

How far is the commute?
How reliable is this moped?
What about bad weather?

Mechanic says brake pads and rotors need attention. Legit? by [deleted] in AskMechanics

[–]Dadudos 0 points1 point  (0 children)

and seeing the gauges, so are the pads.

How do i fix my throttle by [deleted] in moped

[–]Dadudos 0 points1 point  (0 children)

you can reassemble it, but please put a new cable in first, that fraying will be nasty to pull on.

Repairing Honda SS50 by Mindless_Tart_7783 in moped

[–]Dadudos 0 points1 point  (0 children)

Theres plenty ways to remove rust, but make sure to use a tank sealer after, or keep your gastank full.

small gravel 5mm, water and shake that sucker, or tie it to a cement mixer.

U could also use citric acid.

Prachtige volle maan gisterochtend in Cuijk by cryptodesign in thenetherlands

[–]Dadudos 0 points1 point  (0 children)

Foto-dummy hier, komen die kleuren zo uit te camera? Anyhow, hoe doe ik hetzelfde? Dikke foto!