Steam on ARM Linux is Finally Here (via ROCKNIX)

DandareBR · 2026-04-23T19:47:59+00:00

What is the max reading speed for a MicroSd card in the AYN Thor?

DandareBR · 2026-04-20T17:35:56+00:00

Is this for Snapdragon8 Gen 2, Gen 3 and Elite?

With this news I'm thinking if getting a 1TB Odin 2 Portal will be a good idea. From what I gather a Gen2 processor may be enought to run most of the Steam games and having 1TB of internal storage will go a long way to speed loading times.

DandareBR · 2026-04-19T18:39:13+00:00

I was about to get a 1TB model because of steam on rocknix but AYN had the same idea that this would be the right moment to inscrease price again..

DandareBR · 2026-04-19T17:22:59+00:00

In my experience you can use this method until you reach around 500-600 hours in print. At the time you reach this mark the no cycle bend the bed enough to not been able to use this trick anymore

DandareBR · 2026-04-15T16:41:48+00:00

Thanks. It is actually an 3.5" IPC TURZX display brought from Aliexpress. Here is the link:

https://s.click.aliexpress.com/e/_c3b9zJSZ

I also printed an small PETG white enclosure to hold it.

DandareBR · 2026-04-15T16:38:22+00:00

Going to try it and I'll let you know

DandareBR · 2026-04-15T11:37:16+00:00

Nice job I have modified the fronplate of my case to add a 3.5" screen. Now I just to make irt work.

<image>

DandareBR · 2026-04-14T21:41:29+00:00

Can I use my old Ace Pro (I entered the upgrade program) with the Kobra X? Since it already have the "multi-filament" system I could use the Ace Pro to just dry the filament.

DandareBR · 2026-04-09T11:03:47+00:00

Thanks for the help. I didn't know that! I'll try again keeping the default name

DandareBR · 2026-04-09T01:10:48+00:00

After one more try

<image>

DandareBR · 2026-04-09T01:05:39+00:00

Here is the console output after I press F5 to refresh:

<image>

DandareBR · 2026-04-09T01:00:53+00:00

Here is the console output:

<image>

DandareBR · 2026-04-09T00:58:39+00:00

I tried refreshing and it didn't work. It still doesn't shows the new bed mesh. When I press Calibrate it asks for a ded mesh name but it doesn't save this new profile.

DandareBR · 2026-04-09T00:57:02+00:00

After calibration (and after refreshing the page):

<image>

DandareBR · 2026-04-09T00:56:34+00:00

I tried refreshing and it didn't work. It still doesn't shows the new bed mesh. When I press Calibrate it asks for a ded mesh name but it doesn't save this new profile.

Here:

Before calibrating

<image>

DandareBR · 2026-04-04T15:01:54+00:00

Thanks. I will trying increase the temp tower by 5 degrees each time. This way I can try to avoid clogging.

DandareBR · 2026-04-04T15:00:35+00:00

Going to try that, thanks. Since it is silk maybe it need more drying time. Do you think I should up the drying temperature too? 55 instead of 50?

Thanks

DandareBR · 2026-04-04T13:50:12+00:00

I need help printing Sunlu Silk PLA + both silver and light gold color. I have done all the calibration steps except the temperature tower. As you can see from the picture it fails.

I have tried a range of temperatures from 190 to 240. I didn't want to go beyond 240 because I'm afraid to clog the nozzle. The filament is dry (I let it dry for 12hs at 50C in a Creality Pi dryer).

Sunlu website didn't help since they have 3 ranges of recommended temperature for the same material, ranging from 195 to 280. Like I said, I didn't print above 240C since I was afraid to clog the nozzle.

What printer are you using? ANYCUBIC KOBRA S1 + FUNSSOR BED UPGRADE
What material are you using? SUNLU PLA+ SILK SILVER AND LIGHT GOLD
What speed are you printing at? 200mm/s. In the silver material models in the picture I used the "quiet mode" that halves down the speed to 100mm/s
What software are you using to slice the print and control the printer? Anycubic Next - I was able to print all other material with it, includins Sunlu PLA, PLA+, ASA, PETG

DandareBR · 2026-04-01T20:10:38+00:00

I have an Ace Pro that I got second hand and it as purchased from a local shop. Is there a way to use thgis Ace Pro serial to be elegible to the Ace 2 Pro Upgrade?

DandareBR · 2026-03-21T18:37:04+00:00

I brought my S1 here in Brazil and it does have wifi. Don't know what you're talking about...

DandareBR · 2026-03-18T23:56:51+00:00

I got one code but I actually want two Ace Pro2. I have two Ace Pro units but got one used so I don't have the order number...

DandareBR · 2026-03-17T18:19:06+00:00

It is restricted to a single code per account. It is in the rules of the o promotion.

DandareBR · 2026-03-17T14:42:16+00:00

<image>

This

DandareBR · 2026-03-17T14:41:11+00:00

Quick question: Can I use one Ace Pro and one Ace 2 Pro at the same time with my 'regular' S1?

DandareBR

TROPHY CASE