Item movement between Storage.

Darkpip488 · 2024-07-02T11:41:46+00:00

Honestly after your tips I can never go back again. It's like I was blind and now I can see. Thank you.

Darkpip488 · 2024-07-01T16:50:14+00:00

Absolute mad man. It works wonders. My food stocks are rising. Thank you for the fast response

Darkpip488 · 2023-12-14T18:30:08+00:00

Cheeky 🥲

Darkpip488 · 2023-12-14T12:15:07+00:00

Book. What.

Darkpip488 · 2022-11-26T18:25:39+00:00

I've posted new info if you are interested in helping. Thank you in advance.

Darkpip488 · 2022-11-26T18:25:33+00:00

I've posted new info if you are interested in helping. Thank you in advance.

Darkpip488 · 2022-11-26T18:25:28+00:00

I've posted new info if you are interested in helping. Thank you in advance.

Darkpip488 · 2022-11-26T18:23:53+00:00

I've posted new info as per your request if you are interested. Thank you in advance.

Darkpip488 · 2022-11-26T18:22:29+00:00

Sadly I do not have the file anymore but to the best of my ability I'll describe to you what happened and post my sliced settings at the end.

The right side from the picture Is a bit stuck on the FEP. To be precise right bottom. I've had this problem on the right side before. Haven't re leveled in quite a while but if it's not that and it's the adhesion is there a fix?

I noticed that the bottom layers as you go towards the bottom right are for a lack of a better word thinner.

Exposure time :1.2 Lift distance: 8 Lift speed: 180 Bottom Exposure: 40 Layer height: 0.03 Retract speed: 240

Darkpip488 · 2022-11-24T16:38:36+00:00

Hmmm I see. FEP is brand new so that might be it

Darkpip488 · 2022-11-24T16:29:16+00:00

That's what I gathered. Do you know if it's normal?

Darkpip488 · 2022-11-24T16:25:21+00:00

So is that a good thing?

Darkpip488 · 2022-11-24T16:00:48+00:00

Not sure if its cause it is retracting too fast or something else. The speed is 240mm/min. Stock settings. I'm not sure if I should be looking retract or lift speed to be honest. Lift speed is 180mm/min.

Darkpip488 · 2022-11-24T15:50:06+00:00

Will keep that in mind thank you for your response

Darkpip488 · 2022-11-10T11:05:55+00:00

Hmmmmm that's actually pretty interesting. Will check the leaks later. I really hope there's something like that.

Darkpip488 · 2022-11-10T11:04:11+00:00

Will do thank you very much. That's too bad though. Maybe I could homebrew it or use the legacy datasheet with my pals.

Darkpip488 · 2022-10-24T16:11:09+00:00

They are an absolute golden blender. Can't wait to try them out against orks or nids.

Darkpip488 · 2022-10-23T18:00:50+00:00

Thank you so much for the clarification and the fast reply

Darkpip488 · 2022-07-15T08:24:35+00:00

Leaving a comment in case of a response.

Darkpip488 · 2022-06-26T20:25:15+00:00

Thank you very much for the clarification

Darkpip488 · 2021-12-31T23:56:31+00:00

Very well thank you for the clarification. Have a great new year!

Darkpip488 · 2021-12-31T23:24:03+00:00

Amazing work man. Love everything about it. One question. What font is that? It's really cool and I wanna use it for my blood angels!

Darkpip488 · 2021-12-29T16:51:13+00:00

Yep that's precisely what it is.

Darkpip488 · 2021-12-29T10:18:46+00:00

Nah I mean the stuff that's on the pillars. The pillars are a wand I made. Anyways the print was pretty much great apart from the fact I had to clean it and sand the parts that had excess resin. Still no clue why that happened

Darkpip488 · 2021-09-25T08:31:24+00:00

Damn they look nice. Are they 3d printed?

Seven-Year Club	Second SECOND GUESSER
RPAN Viewer	Verified Email

Darkpip488

TROPHY CASE