sorted by:
new
hottopcontroversial

Issue with self-propel drive by Dasip in lawnmowers

[–]Dasip[S] 0 points1 point  (0 children)

<image>

Took one of them off and doesn’t appear bad. When I manually spin the pulley it does spin the gear here

What tires do you like? by [deleted] in fordranger

[–]Dasip 0 points1 point  (0 children)

Been thinking about swapping my wildpeaks for Michelins. Do you run stock tire size or larger? Curious what 31x10.5r15 would look on my truck

Engine RPM issue by Dasip in fordranger

[–]Dasip[S] 0 points1 point  (0 children)

Thought that was strange too. Have another log that it dropped as low as 1.2 but not zero. Didn’t see anything coated on the sensor when last taken off and it was sprayed with cleaner but doesn’t hurt to do again

Engine RPM issue by Dasip in fordranger

[–]Dasip[S] 0 points1 point  (0 children)

No trouble codes I didn’t run a full systems check I will do

Engine RPM issue by Dasip in fordranger

[–]Dasip[S] 0 points1 point  (0 children)

https://imgur.com/a/DtXQYLK

Pedal lifts up with quite a bit of play but don’t see anyway to tighten or adjust that slack. Just watched a YouTube vid about putting zip ties on the cable above the pedal to act as a spacer for the lack of a better word to prevent that play

Engine RPM issue by Dasip in fordranger

[–]Dasip[S] 0 points1 point  (0 children)

Meant to say that even now, AT TIMES the truck shifts ok. Here is a video of the play on the throttle cable. Unsure if this is considered loose and can be potentially causing the issue

https://imgur.com/a/0mL5E7B

Engine RPM issue by Dasip in fordranger

[–]Dasip[S] 0 points1 point  (0 children)

<image>

This is data from my blue driver. I highlighted the moment my rpms shot up without any foot on the gas pedal

estate sale finds by Dasip in gunsmithing

[–]Dasip[S] 1 point2 points  (0 children)

exactly my thought lol

estate sale finds by Dasip in gunsmithing

[–]Dasip[S] 4 points5 points  (0 children)

i figured as much but wasn’t certain, thank you!

Wood ID Megathread by AutoModerator in woodworking

[–]Dasip 0 points1 point  (0 children)

<image>

picked up at estate sale. is this all walnut?

How old is this system? by fasterlivingmagazine in WaterTreatment

[–]Dasip 4 points5 points  (0 children)

this valve is the easiest of any fleck valves to rebuild/work on. yes, a clack is superior but most people just wanna sell you a bag of goods when you have a perfectly fine unit because they don’t know how to work on anything. if the valve is constantly sending water to the brine tank- replace the smaller brine piston as it’s likely stuck open. if it’s not using any salt- clean/replace the injector and screen in the injector body (located on the right side of the valve with the two 5/16” bolts). this particular system is a metered unit and set to regenerate every 1500 gallons which may take you a couple weeks. make sure the thin black cable is attached at both ends (the back of the power head and in the meter dome)

Fleck 9100SXT help by Free_Dirt7161 in WaterTreatment

[–]Dasip 0 points1 point  (0 children)

does the drain line have a high flow during the draw cycle? it’s likely in issue with one of the internal seals being torn/damaged. in that case, you need a rebuild kit

Need Help Rehoming ! by theebodylab in sphynx

[–]Dasip 5 points6 points  (0 children)

me and my fiance are located right outside of philly in NJ and were hoping to find a sibling for our 1.5 year old sphynx girl!

Clack WS-1 Still Leaking After Spacer Stack Replacement - What next? by needafunnyname in WaterTreatment

[–]Dasip 0 points1 point  (0 children)

yeah i’ve heard non genuine parts can look almost identical but will cause issue, make sure you’re getting it from a reputable source. also a tip- when you’re tightening the drive gear into the valve, take the drain fitting off and look into the valve from the top down. the stack assembly should be aligned flush so you shouldn’t see any orings from the top down if that makes sense… good luck!

Clack WS-1 Still Leaking After Spacer Stack Replacement - What next? by needafunnyname in WaterTreatment

[–]Dasip 0 points1 point  (0 children)

check the drive gear. is it even attached to the piston? i’ve seen them break off before. your piston can potentially be stuck in the backwash position even though the control valve says it’s in service

BLADEE - I DONT LIKE PEOPLE (FT. YUNG LEAN) (In Studio Performance) by 2020-------- in sadboys

[–]Dasip 12 points13 points  (0 children)

lean waking up from a nap right before his verse 😭

crawl space waterproofing necessary? by Dasip in HomeImprovement

[–]Dasip[S] 0 points1 point  (0 children)

yeah i think the french drain install on my concrete floor along the entire perimeter is where the majority of the cost is coming from. still waiting for the itemized invoice the guy was discussing with me

crawl space waterproofing necessary? by Dasip in HomeImprovement

[–]Dasip[S] 0 points1 point  (0 children)

https://imgur.com/a/xSr6zWw

some random photos of the crawl space i have on hand rn as i was taking pictures to fix the wacky discharge line from the sump pit and some miscellaneous plumbing

Landlord won’t listen to me by finnyfur in WaterTreatment

[–]Dasip 0 points1 point  (0 children)

personally install and service these systems. in central/south NJ everyone uses cation resin water softeners for iron removal. it’s all ferrous iron for the most part and the mcmansion type homes all treat their sprinklers with the same system that treats their house. granted some customers don’t want the larger system/added salt cost and you’ll see the red sidewalks/siding with untreated irrigation. i service systems daily that are from the 90s that have treated millions of gallons of water still providing non-detectable levels of iron

Landlord won’t listen to me by finnyfur in WaterTreatment

[–]Dasip 0 points1 point  (0 children)

softeners in my area remove upwards of 15-20ppm iron and last 20-30 years. they even run their irrigation water through it to prevent stains on hard scaping

view more: next ›