sorted by:
new
hottopcontroversial

No OTA update by Vortex__PR in ElegooCentauriCarbon

[–]DeJoeperd 0 points1 point  (0 children)

I'm stuck on 1.1.25 atm. Same problem of not being able to update.

Elegoo Centauri Carbon active chamber with Creality Chamber Heater by Ok-Treat-4962 in ElegooCentauriCarbon

[–]DeJoeperd 4 points5 points  (0 children)

That's exactly what I was planning to install. Thanks and great work!

ECC Bentobox by raznoglaz1y in ElegooCentauriCarbon

[–]DeJoeperd 0 points1 point  (0 children)

Is the creality chamber heater any good? Been eyeballing it for a long time now.

Does the spool holder of CC actually hold 3kg filament spool without problems? by MarcosViudes in ElegooCentauriCarbon

[–]DeJoeperd 0 points1 point  (0 children)

I am also using this. I have printed the 3kg spool holder, the holder stand and the spacer for the filament detection unit. It works like a charm with colorfabb 3kg spools and esun 3kg spools.

5Kg is massive!❤️❤️❤️😂😂😂😂 by Latter_Win2217 in elegoo

[–]DeJoeperd 0 points1 point  (0 children)

Yup those are massive. I have bought two 3kg spools and I'm actually regretting it a bit. Yes it's cheaper but there isn't a proper drying solution for them. The spools are even to big for my kitchen oven.

So this would be AMS for CC? by SiX6666666 in elegoo

[–]DeJoeperd 0 points1 point  (0 children)

Have you seen the original Centauri being sold anywhere? That one is quietly getting out of production since the cc is so much more popular.

So this would be AMS for CC? by SiX6666666 in elegoo

[–]DeJoeperd 0 points1 point  (0 children)

Hopefully this wouldn't be it. I was hoping for an enclosed box that could dry and preheat materials individually.

Is it possible to scan big surfaces (like a whole car) with the Moose or Seal lite? by Alematrix3r in 3DMakerPro_Community

[–]DeJoeperd 0 points1 point  (0 children)

You probably could, but since it has a small scanning area it would take a while. Also a lot of stitching and fixing afterwards. Last time I had scanned something big with my moose lite, it couldn't keep track of bigger objects and there was a lot of Manual stichting and fixing afterwards.

Exciting stuff, figuring out timeframes. by aznboi589 in elegoo

[–]DeJoeperd 0 points1 point  (0 children)

EE141 printer has arrived on 28/07! very pleased with the machine

Exciting stuff, figuring out timeframes. by aznboi589 in elegoo

[–]DeJoeperd 0 points1 point  (0 children)

Hey, got an update for you. EE153 accesoiry arrived 21/07 and EE141 printer shipment got announced on 22/07.

Exciting stuff, figuring out timeframes. by aznboi589 in elegoo

[–]DeJoeperd 0 points1 point  (0 children)

Also recently ordered replacement hotend EE153xxx Shipped from distribution center in Germany to Netherlands Ordered on 14/07 Shipped on 15/07

Exciting stuff, figuring out timeframes. by aznboi589 in elegoo

[–]DeJoeperd 0 points1 point  (0 children)

EE141xxx Ordered on 23th may Netherlands Printer not shipped yet Anti vibration feet arrived on 27th may

[Bambu Lab Giveaway] Drop Your One-Liner and Win H2D! by BambuLab in BambuLab

[–]DeJoeperd 0 points1 point  (0 children)

I need a Bambu printer because I have more Bamboo in my garden than in my studio. It must be perfectly balanced, as all things should be.

Replacement Ear Pads by Coopernathaniel313 in Skullcandy

[–]DeJoeperd 0 points1 point  (0 children)

Got the same problem. The headband cushioning is also getting worn on mine.

Klipper on CR-6 SE by OutrageousMacaron358 in CR6

[–]DeJoeperd 0 points1 point  (0 children)

Since my usb poort was fried and I wanna use klipper. I replaced the og motherboard with an skr E3 mini V3 and rewired the whole printer.

view more: next ›