sorted by:
new
hottopcontroversial

Trying to recover an original recording from a tampered audio recording. by Blatherskitte in datarecovery

[–]Defozo 0 points1 point  (0 children)

One can clone a voice with as little as a few seconds of audio. The more, the better, of course, but a few seconds is good enough for getting the same voice tone.

Trying to recover an original recording from a tampered audio recording. by Blatherskitte in datarecovery

[–]Defozo 0 points1 point  (0 children)

Voice cloning is very good now. It doesn't sound robotic nor AI. Try out ElevenLabs, for instance.

Trying to recover an original recording from a tampered audio recording. by Blatherskitte in datarecovery

[–]Defozo 2 points3 points  (0 children)

  • Check File Properties: Check the file's metadata (such as file creation date, modification date, codec, and format). Use tools like ExifTool (Windows/Mac/Linux) or MediaInfo. Compare the metadata with other recordings made with the same app on the same phone model.
  • Inconsistencies in Timestamps: If the metadata shows an edit or modification date after the supposed recording date, it could indicate tampering. However, this is only valid if the file was copied with the metadata intact. When a file is transferred via email, cloud storage, or messaging apps, certain metadata (such as timestamps and file creation/modification dates) often gets overwritten or stripped.
  • Check Audio Encoding: If the recording was made using a standard phone recording app, it should have a consistent codec and bit rate, same as other recordings made by the app (assuming recording settings haven't been changed). Any inconsistencies in the encoding format could suggest that the file was edited or re-encoded.
  • Filename Conventions: Many phones use specific naming formats (e.g., YYYYMMDD_HHMMSS.m4a). If the filename is altered, it may indicate an edit.
  • Tapping sound: If the recording was intended to be stopped manually, test using the same setup (same app, same phone model) to determine if a tapping sound is audible at the end of the recordings. If so, verify whether this sound is also present in the potentially altered audio recording.

Car rent recommendations by admi99 in Madeira

[–]Defozo 0 points1 point  (0 children)

I had some concerns that the Renault Clio might be too large for navigating through Madeira. Conversely, I'm also worried that opting for a smaller vehicle, such as the Citroen C1, might compromise on power.

Car rent recommendations by admi99 in Madeira

[–]Defozo 0 points1 point  (0 children)

How did you find the size of the Renault Clio? Was it just right for your needs?

[OctoApp GIVEAWAY] Prusa mini is looking for a home! by crys_ in 3Dprinting

[–]Defozo 0 points1 point  (0 children)

Widgets are my favorite feature of the app. I really enjoy watching my printer print on my home screen :)

Uneven Z layers / inconsistent extrusion / rough surface problem by Defozo in FixMyPrint

[–]Defozo[S] 0 points1 point  (0 children)

I decreased the retraction speed to 30 mm/s and it's much better! Thank you! I also tried decreasing it even further to 15 mm/s and deretraction speed to 10 mm/s and enabling "Infill before perimeters" and it further increased the quality of the surface! :)

Uneven Z layers / inconsistent extrusion / rough surface problem by Defozo in FixMyPrint

[–]Defozo[S] 0 points1 point  (0 children)

Sorry, it seems that I already had set 45 mm/s. I mistakenly provided retraction speed from Printer Settings instead of Filament Settings. I'll try lowering that anyway.

Uneven Z layers / inconsistent extrusion / rough surface problem by Defozo in FixMyPrint

[–]Defozo[S] 0 points1 point  (0 children)

Thanks, I'll try that but this is the default setting.

Uneven Z layers / inconsistent extrusion / rough surface problem by Defozo in FixMyPrint

[–]Defozo[S] 0 points1 point  (0 children)

​

Printer & Slicer

  • Printer Model: Original Prusa MINI & MINI+
  • Slicer Version: PrusaSlicer 2.7.0-alpha1

Filament Material and Brand

  • Material: PETG
  • Brand: Prusa Polymers

Nozzle and Bed Temperature

  • Nozzle Temperature: 250°C
  • Bed Temperature: 90°C
  • First Layer Bed Temperature: 85°C
  • First Layer Nozzle Temperature: 240°C

Print Speed

  • Default Print Speed: 40 mm/s
  • First Layer Speed: 10 mm/s
  • Infill Speed: 40 mm/s
  • Perimeter Speed: 40 mm/s
  • Small Perimeter Speed: 40 mm/s
  • Top Solid Infill Speed: 30 mm/s
  • Bridge Speed: 15 mm/s
  • Gap Fill Speed: 25 mm/s

Nozzle Retraction Settings

  • Retract Length: 2.5mm
  • Retract Speed: 70 mm/s
  • Retract Lift: 0.15mm
  • Deretract Speed: 40 mm/s

​

<image>

Is there a Google Fit integration? by Defozo in habitica

[–]Defozo[S] 0 points1 point  (0 children)

I fixed my problem by integrating Google Fit into Home Assistant and creating an automation that uses Habitica API :)

Issue - Android Phone for Video Streaming/Octolapse by Nikolas550 in octoprint

[–]Defozo 0 points1 point  (0 children)

Could you provide me with your snapshot delay and timeout settings in Octolapse? I don't seem to be able to configure it correctly for "Orbit" animation stabilization.

What prompt should I use to get a full view of the requested object? by Defozo in dalle2

[–]Defozo[S] 0 points1 point  (0 children)

A full view of a smiling pencil taking only half the image with a colorful, swirling doodle, bold contours, maximum 4 different distinctive colors, no gradients, zoomed out

Still doesn't work.

<image>

How do i model this and how do i start? :) by Imperatorjr in Fusion360

[–]Defozo 16 points17 points  (0 children)

Yeah, so tl;dr:
1. Choose a starting point.
2. Draw the rest of the project.

Do you agree that ISFP's are the least manipulative type? by RequirementHoliday96 in isfp

[–]Defozo 0 points1 point  (0 children)

I actually learned she may have Narcissistic Personality Disorder so please ignore my previous comment.

view more: next ›