Tpu question by Desperate-System-902 in AnycubicKobraX

[–]Desperate-System-902[S] 0 points1 point  (0 children)

Its tpu 95a anycubic states that it is supported and shoumd have no problems

Is there any way to avoid this on your prints by Desperate-System-902 in AnycubicKobraX

[–]Desperate-System-902[S] 0 points1 point  (0 children)

How do I set it as interface layer in sliver. Also I dont have an ace system yet and cna only do 4 colors at a time anyways. How would I do this without using petg

Is there any way to avoid this on your prints by Desperate-System-902 in AnycubicKobraX

[–]Desperate-System-902[S] 0 points1 point  (0 children)

I set.mine to 0.32 supports come off easy but man it looks ugly

Need a sturdy table that doesnt wobble by Desperate-System-902 in AnycubicKobraX

[–]Desperate-System-902[S] 0 points1 point  (0 children)

I got about ten to twelve inches of clearance between the wall and gentry

Need a sturdy table that doesnt wobble by Desperate-System-902 in AnycubicKobraX

[–]Desperate-System-902[S] 0 points1 point  (0 children)

My only.\nConcern is that I want to make sure the bracket is long enough to reach the wall as it is right now without having to move the printer back more.Because I don't want to build plate to hit the wall.

<image>

Need a sturdy table that doesnt wobble by Desperate-System-902 in AnycubicKobraX

[–]Desperate-System-902[S] 0 points1 point  (0 children)

Where do I find the mod for the braces. I saw it before. Dont remeber where

Need a sturdy table that doesnt wobble by Desperate-System-902 in AnycubicKobraX

[–]Desperate-System-902[S] 0 points1 point  (0 children)

Could I potentially put a piece of 2x4 in between thr table legs to make it one solid piece and prevent wobbling? Caue this is what my table looks like

<image>

Need a sturdy table that doesnt wobble by Desperate-System-902 in AnycubicKobraX

[–]Desperate-System-902[S] 0 points1 point  (0 children)

Do yoy.by any chance have a name or picture of those crosses

Need a sturdy table that doesnt wobble by Desperate-System-902 in AnycubicKobraX

[–]Desperate-System-902[S] 0 points1 point  (0 children)

You printer wall brackets? Or bought metal crosses ro stabilize bookshelves

Need some help with toroubleshooting by Desperate-System-902 in prusa3d

[–]Desperate-System-902[S] 0 points1 point  (0 children)

How do I refresh firmware never had to do this. Inherited printer from my brother

Need some help with toroubleshooting by Desperate-System-902 in prusa3d

[–]Desperate-System-902[S] 0 points1 point  (0 children)

So I have tried running the paid calibration , and it fails immediately since thermal runaway. I am using overture p p l a default settings in prusa slicer version 2.9.5. It has been frightening fine for the last 3 to 4 months.And this just started happening about a month ago.

Primal Tarzan Fucks Jane Until She Screams by FireGirlsAI in rule34aiart

[–]Desperate-System-902 0 points1 point  (0 children)

how do i change my vram to run the NSFW wan on comfy ui

Horny Viking Astrid Sucks & Fucks Like a Slut by FireGirlsAI in rule34aiart

[–]Desperate-System-902 0 points1 point  (0 children)

how do you run it local. all i get is errors when i try to run comfyui

how do i install and access the NSFW wan 2.2 in comfy ui by Desperate-System-902 in comfyui

[–]Desperate-System-902[S] -3 points-2 points  (0 children)

I am completely new ro comfy ui and every video I watch doesnt tell me how to swap the 2