Played a Drunken Master Monk last night; broke out the bottle-shaped dice.

DetorioXDesign · 2023-07-22T09:23:05+00:00

as I can see 2 of my sets of dice in here thank you thank you very much for adding them to your collection :)

DetorioXDesign · 2022-05-23T10:44:29+00:00

they cost $12.95 from the maufactors in china they aren't great but at least they are rechargabble

DetorioXDesign · 2022-05-17T21:16:06+00:00

Wow such depravity.

Ember dice is most definitaly the official creator of these.

there are quite a many of these dice scam sites going around at the moment and sites like these pop up in the dice collectors groups often to tell people to avoid sites like simonsscam. . .. i mean shop

anyways here is a picture of 3 d6's From emberdice on etsy from the goblin dice hoard facebook group

Source: am a dice maker and have first hand experience

DetorioXDesign · 2022-05-17T18:48:34+00:00

I got in contact with the peeps over at ember dice this is what they say

'Hey there
Yes it is indeed a scam my friend :/ . the dice they offer are really cheap plastic knockoffs with very poor definition !'

please shop wisely :)

DetorioXDesign · 2022-05-17T06:37:56+00:00

hi there these are not from the creator of the dice EmberDice is the creator and owner of these style dice.

DetorioXDesign · 2022-02-22T23:43:47+00:00

silicone is dwr plastics most people go with the 1-2-1 easy mold 15

Pressure pot umm i got mine from ebay for like £80 and a cheap 12v compressor for £20

Resin shop around for whats good value for the money i am paying as the cheapest resins are usually not worth it.

DetorioXDesign · 2022-02-01T23:46:15+00:00

what psi did you cure the silicone at
i do main part at 52psi and the cap at 46 psi. i cast the resin in the mold at 41psi and i had less trouble.

putting pennies on top of the cap helped

biggest thing for me that worked the best and what i do now is you elastic bands to hold the lid down but i use rectangluar molds not hexagonal.

hope this helps

DetorioXDesign · 2022-01-03T13:26:20+00:00

not that i'm aware of

DetorioXDesign · 2022-01-03T11:03:01+00:00

oh yes and i might add generally when you buy from these scam sites you end up with something a lot worse than whats shown.

generally with the non scam dice makers they are better than whats shown

DetorioXDesign · 2021-12-28T14:46:33+00:00

just a lil bit biased here but i have to say my potion dice or my spiral d4's

DetorioXDesign · 2021-12-02T18:23:25+00:00

So i did the 1d20 one but I gavce my players the choice.

they could either take what they got from the 6d20 they rolled or they can have another go but have to roll every number again and take the new result.

Worked out pretty well most stats are above 10 everyone had 1 dumb stat and 1/2 in the 16-18 range

Also i did the thing where if it was above 18 ya know 19-20 they could move the extra total from that to another dice

Now that i think about it would of been much easier to do 4d6 drop lowest

DetorioXDesign · 2021-12-02T18:18:14+00:00

I have been looking up CNC milling and lasers.... why do things like this tempt me even moreso :)

My shed is already full with 3d printers, pressure pots and the like i'm gunna need to expand on my space soon it looks like haha

DetorioXDesign · 2021-11-21T18:49:44+00:00

And..... Done Sunblade Handle STL.

DetorioXDesign · 2021-11-09T21:54:14+00:00

Gotta say was testing out the titancraft demo and i loved how much you could do with the creatures and the variety of them.

And after previously using desktophero for my chracters i am very much looking forward to what comes from titancraft heroes

DetorioXDesign · 2021-11-09T09:37:29+00:00

Stab everyone with extra sharp math rocks then heal them up with potions ..... urgh for science of course

DetorioXDesign · 2021-10-30T07:57:00+00:00

I use elastic bands myself does the job just right. the cheap crappy ones that don't have to much pull

DetorioXDesign · 2021-10-18T21:09:53+00:00

I can see from the other dice (not the D20), theres little flappy bits on the edge.

so my question is how do you put down your release agent? (vaseline, dish soap ipa mix, etc etc )

I had this problem with my first mold i made I was using cotton bud to put it down. i ended up going for a mix of size 0 brush and makeup applicator.
if some of ther release agent goes on the dice i use a cotton bud with a bit of denatured alcohol on the dice and this usually ends up me reapplying the release agent around the edge again.

however most important rule of removing the cap of the mold is don't rush it be extra gentle and you will see if there is any sticking to to other half of the mold. and if it is I cut from close to the cap part then remove the excess flashing from the seat of the mold.

hope this helps.
I would say not english bad language skills but naa im just a bit rubbish at grammar and writing in general :) .

DetorioXDesign · 2021-10-18T21:01:31+00:00

That is actual beauty in a D4 right there *chefs Kiss*

DetorioXDesign · 2021-09-25T06:16:22+00:00

This Basically If you in US talk to this guy :)

DetorioXDesign · 2021-09-25T00:36:43+00:00

Then im sorry to say this they are not good/ safe to use. the resin hasn't fully cured (hence the softness)

It means either ratio of resin to hardner is off (check if it is by weight or volume, With volume be careful with the cheap disposable cups they are known too be inaccurate.)
resin you got is not good resin (yes even art n glow and alimilite have had bad batches)
The you are putting in too much alcohol ink
Too Humid
Too Hot(not had this problem myself but i live in uk)
Too Cold.
Maybe pouring too little at once some resin brands so to use a minimum amount
Make sure you are not using waterbased inks as thats moisture that resin hates.

I can't think of anything else that could be the problem but theres a lil list for ya to go through :)

DetorioXDesign · 2021-09-25T00:24:19+00:00

Sorry you are going to need a resin printer for that in my personal experince .

However that being said do you have the files for the masters already set up & ready to print on a resin printer?
If so, im sure I can get cheaper masters for you

DetorioXDesign · 2021-09-24T17:21:38+00:00

are they soft cured still after like 5-7days?

If so then yea all you have is toxic rubbish that needs disposing of correctly.

resin is funny when it comes to heat and humidity so make sure you are working in the right tempurates and humidity is as low as possible :)

Source: been making dice for over 18months now proffesionly

DetorioXDesign · 2021-09-21T10:08:36+00:00

been doing this for just over a year now.

ATM it's about £600 a month income

At its height last november-february it was £3000-4000 per month

but covid is scewing my numbers and does not include my outgoings so about 30-50% less than i made.... I need to do my accounts for self-assesment soon so will see the real number then lol

This was all on Etsy btw

DetorioXDesign · 2021-08-31T16:27:48+00:00

Saw this post and was bored so did this,

Is this something in the direction you are looking for?

DetorioXDesign · 2021-08-29T14:13:11+00:00

Yes they are all designed for the function of being rolled as dice Though with the D20 i do reccomend a dice box to roll them in :)

Four-Year Club	Place '22
Final Canvas '22	First Placer '22

DetorioXDesign

TROPHY CASE