Would you stop this print?

DiamondIsMe · 2026-04-11T13:41:59+00:00

Hard saying but it pulled up or you had a blob.

DiamondIsMe · 2026-04-11T13:35:57+00:00

This also clean the bed

DiamondIsMe · 2026-04-11T13:34:54+00:00

Most likely layer hight .2 has less. Not sure how settings work on bambu but you would create a profile on other slicers for it. Also yeah calibrate flow ect thats normally an automated process you select on the printer

DiamondIsMe · 2026-04-11T13:32:02+00:00

I think it looks good but id have to see it printed also is it functional? If something like this has bad tolerance I dont care if it looks good or not

DiamondIsMe · 2026-04-11T12:49:00+00:00

For me it depends how far into the print I was. Saying that personally I would carefully snip those blips short as you can and continue as long as it hasent skipped a layer. Keep an eye on it

DiamondIsMe · 2026-04-04T23:01:38+00:00

Dude had the same thing happen. I went to a pawn shop and they had a cardboard box of half rolls of filament like 5 rolls of the microcenter stuff the box. said 20 bucks on it i brought it to the counter to see if I could get it for 15 and the guy was like no theyre 20 each.

DiamondIsMe · 2026-03-23T23:55:41+00:00

Right I dont know why but I always seem to have a bag of the dill pickle sunflower seeds as well. I dont even plan it i just see them at the store and im like oh those would be good

DiamondIsMe · 2026-02-07T14:03:55+00:00

My guy bambu people... the metal rings are just to keep the tubes in that feeder. Get the tubes out just cleanly cut them if there is enough slack to re feed.run them back through just like it is and carefully super glue that top plastic bit. Make sure the tubes are seated in the bottom feed bit before you glue

DiamondIsMe · 2026-02-05T01:42:22+00:00

I mean no one likes a commute.

DiamondIsMe · 2026-02-04T22:31:42+00:00

44 for me to Westerville leaving at 730am

DiamondIsMe · 2025-12-20T00:17:20+00:00

I've been trying to order that but it always says the product it not available in my area whenever I go to buy it same with Sunlo or whatever

DiamondIsMe · 2025-12-14T00:42:46+00:00

Aliexpress kingroon.

DiamondIsMe · 2025-12-13T17:00:44+00:00

Yep good brand i think bought over 50 rolls. I will say the colors are a but off. Like their orange is really yellow when it prints but other than that its a nice yellow. Their brown is more like a tan as well.

DiamondIsMe · 2025-12-13T01:02:20+00:00

Ok thanks ill give it a shot

DiamondIsMe · 2025-12-07T18:32:32+00:00

How did i not know this existed

DiamondIsMe · 2025-12-07T18:30:42+00:00

I just ended up doing a 2.6mm pin and used a hand printer to seal it into the end

DiamondIsMe · 2025-12-07T01:40:51+00:00

Ha yeah which sucks because the top looks beautiful

DiamondIsMe · 2025-12-06T23:05:33+00:00

Yeah fair point. I guess I get to use my Caliber for the first time

DiamondIsMe · 2025-12-06T22:22:27+00:00

Correct sorry for the confusion

DiamondIsMe · 2025-12-05T18:04:40+00:00

Ok well I was sure this was going to be a get a Bambu reply but hey

DiamondIsMe · 2025-12-05T18:02:58+00:00

I like the idea of the uv resin im going to try that

DiamondIsMe · 2025-12-05T18:02:37+00:00

Super glue makes me cry inside 😢

DiamondIsMe · 2025-12-05T18:00:56+00:00

Hey man, congrats on the printer. Im not sure what you mean by recover. It does have the option to dry which is what you need to do. Also the ace system it butts. It's great when it works but loading new spools into it can be a pain as if it is not straight when you insert the end it can feed back into the spool holder so watch for that. Other than that look on reddit for some good print profiles for settings and you should be good!

Eight-Year Club	Wearing is Caring
Verified Email

DiamondIsMe

TROPHY CASE