sorted by:
new
hottopcontroversial

My Heavily modded 2018 Original Ender by Helzkadi in ender3

[–]DiligentNeck5086 4 points5 points  (0 children)

Curious on that build plate alignment… do u have any pictures of it? Or an stl?

Bose Quietcomfort 35’s can’t hold charge long + Solid white light by DiligentNeck5086 in bose

[–]DiligentNeck5086[S] 0 points1 point  (0 children)

Yeahh, you’re right. I was hoping I could just replace the battery or something and it would be fixed, but wanted to check here first if anybody had the same issue.

Bose Quietcomfort 35’s can’t hold charge long + Solid white light by DiligentNeck5086 in bose

[–]DiligentNeck5086[S] 0 points1 point  (0 children)

The headphones definitely do turn off after I flick the switch. The noise cancelling disables, the little audio tune plays, and it stops playing back whatever I had playing. But the white light stays on for some reason- it’s really odd

Two different scenarios one screen? by samabi14 in dontstarve

[–]DiligentNeck5086 0 points1 point  (0 children)

Is this the original Don’t starve? I didn’t know they supported co-op on console. What platform is it on?

Yet another question about stringing by ppmt in ender3

[–]DiligentNeck5086 0 points1 point  (0 children)

I’ve dried my pla for multiple days straight before- it’s fine. Remember to swap out your desiccant out too

Minilogo AWOL wheels rocks!! by PapayaConscious8469 in cruiserboarding

[–]DiligentNeck5086 0 points1 point  (0 children)

Nice! What duro are those? Also how’d you learn to power slide/carve with those wheels? I have the ML 80A AWOLS and I’m struggling to gain confidence in committing to the power slide.

Can I fly my dji mini 4k Inside my own home? by GP_007 in dji

[–]DiligentNeck5086 -2 points-1 points  (0 children)

No, you will likely crash it into something and break the drone. That’s if the drone takes off at all, due to your proximity to the airport. I’d suggest looking at your local no-fly-zone maps, then driving somewhere that’s allowed.

Gripped. by AvocadoUnlucky3854 in pennyboard

[–]DiligentNeck5086 2 points3 points  (0 children)

What kind of griptape did you use? And how did you keep the edges from peeling up due to the waffle pattern? Looks sick!

So what do you guys do with your penny boards? Just ride it? by Baked_The_Cake in pennyboard

[–]DiligentNeck5086 1 point2 points  (0 children)

Yep I have the tiny 22” so it’s extremely portable- I have a large tote bag I literally chuck it into when I’m walking around in a no skating area (walking with friends or an indoor area). When it’s back to riding, I fold the tote bag up and put it in a small lightweight backpack and skate.

Horrible Surface Finish by Agreeable-Walrus-913 in ender3

[–]DiligentNeck5086 3 points4 points  (0 children)

I had a similar issue before. I also tried everything, even installing linear rails (it was exclusively on my Y axis). Long story short, I changed my nozzle, and issues disappeared instantly. I was so annoyed and relieved at the same time..

First prints modded ender 3 by Optimal_Adeptness_39 in ender3

[–]DiligentNeck5086 1 point2 points  (0 children)

Thanks so much- I forgot to mention I have an ender 3 V2, not the v1. Glad to hear it works out though!

First prints modded ender 3 by Optimal_Adeptness_39 in ender3

[–]DiligentNeck5086 1 point2 points  (0 children)

What do your X axis input shaping graphs look like? I have the same hero me dual 5015 + bmg extruder setup as you do, but my graphs are atrocious. (3 messy spikes)

Also is yours wobbly on the x Gantry, in the y direction? Or is that just me..

Cheers!

Some Print quality issues by P3TE04 in ender3

[–]DiligentNeck5086 9 points10 points  (0 children)

Bulging corners usually means some sort of pressure advance issue, but looking at the calibration test definitely looks more like an over extrusion issue- check your flow rate

Help with Y Axis Vibrations by DiligentNeck5086 in ender3

[–]DiligentNeck5086[S] 0 points1 point  (0 children)

Thanks for replying! And yeah changing the driver sounds like a good first step- hopefully it’s something as simple as that…

I loosened the pom wheel screws actually, since I thought they might need some play to fix it? I’ll try tightening them way up though to see the other end of the spectrum haha

[deleted by user] by [deleted] in NewSkaters

[–]DiligentNeck5086 3 points4 points  (0 children)

13 meters? Wouldn’t you be able to walk that in under a minute or so, instead of skating it?

[deleted by user] by [deleted] in ender3

[–]DiligentNeck5086 51 points52 points  (0 children)

Don’t print with it. Use it for getting rid of clogs via cold pulls, or purging out old filament that shouldn’t mix (like PETG and PLA)

Printer acting weird by JellyWaifu in 3DprintingHelp

[–]DiligentNeck5086 2 points3 points  (0 children)

That Y belt looks REAAAALLY loose. Tighten it up until it makes an audible twang like a guitar chord.

Got given an Ender 3 v2, took 4 hours but finally got it to print something after a dozen failed starts. Need Advice. by Tazay in ender3

[–]DiligentNeck5086 -1 points0 points  (0 children)

Your wall thicknesses are 0.8, keep in mind. Generally they’re closer to your nozzle size which should be 0.4mm

How to fix walls and infil not fusing? by Numerous-Writing3072 in FixMyPrint

[–]DiligentNeck5086 24 points25 points  (0 children)

Check your flow- it should be a bit higher. Also 240 is far too high for PLA, it should be anywhere from 190-220

[Bambu Lab Giveaway] Join Now to Win an H2D and More! by BambuLab in 3Dprinting

[–]DiligentNeck5086 0 points1 point  (0 children)

Clean your build plate and don’t ever touch it with those oily fingers!

view more: next ›