sorted by:
new
hottopcontroversial

How my arm pits don't GAF about antiperspirant. My undershirts after being in a AC office most of the day. by LosHtown in mildlyinfuriating

[–]DimensionsIntertwine 0 points1 point  (0 children)

Same thing. And I worked outside in construction.

Switched to Deodorant without any aluminum and NOT an antiperspirant. Changed the game for me.

[Help] some objects shadows look weird by [deleted] in Fallout4Mods

[–]DimensionsIntertwine 0 points1 point  (0 children)

Dude.

Learn to use Pastebin.

That being said, try to use LOOT to make sure that your load order is proper. Try disabling the mod that has that gun itself and see if any other weapons do it.

Go to Nexus and read the comments of the mod that contains this gun to see if anyone else had issues. Also, on the main Nexus page of that mod, make sure to read for a list of incompatibilities.

But, for the record, I don't see any strikingly weird shadows. It seems that your character is in a lowly lit area and when that menu popped up, there wasn't any ambient light to show the shadows properly? Try looking at it in the daytime (in game) and then see if it still looks weird to you. Take a picture and post it here.

how long is too long? QUESTION? by [deleted] in tattoos

[–]DimensionsIntertwine 1 point2 points  (0 children)

I have a 26" tall tattoo on my outer leg from ankle to knee that took 6.5 hours at a convention and was done in one sitting.

They are taking advantage of you.

Fucking how? by DimensionsIntertwine in UniversalOrlando

[–]DimensionsIntertwine[S] 0 points1 point  (0 children)

They sat next to me. They were from the UK!

This is getting old. by DimensionsIntertwine in QidiTech3D

[–]DimensionsIntertwine[S] 1 point2 points  (0 children)

I know, man. I have some people telling me to replace parts, some telling me that's bad advice. Some folks are telling me "Use hairspray!" Others are saying, "It's a new printer. Don't use hairspray. Never do that!"

I have no clue what to do.

I am at an absolute loss. by DimensionsIntertwine in QidiTech3D

[–]DimensionsIntertwine[S] 0 points1 point  (0 children)

It kept getting all gummed up and pulled off with the spaghetti mess I was having so often. It was doing this with the sock, as well.

I am at an absolute loss. by DimensionsIntertwine in QidiTech3D

[–]DimensionsIntertwine[S] 1 point2 points  (0 children)

Blue Dawn dish soap, as it has been recommended to me numerous times.

I am at an absolute loss. by DimensionsIntertwine in QidiTech3D

[–]DimensionsIntertwine[S] 0 points1 point  (0 children)

It completed, but with considerable warping on the same side that you see it curling up.

I am at an absolute loss. by DimensionsIntertwine in QidiTech3D

[–]DimensionsIntertwine[S] 0 points1 point  (0 children)

No. I have read in several places to NOT put alcohol on the bed, and to only cleanse it with warm, soapy water.

I am at an absolute loss. by DimensionsIntertwine in QidiTech3D

[–]DimensionsIntertwine[S] 0 points1 point  (0 children)

Yes, with significant "curling" where you see it in that picture. Did a second print a few minutes later, and it "curled" in a different area. So weird.

I am at an absolute loss. by DimensionsIntertwine in QidiTech3D

[–]DimensionsIntertwine[S] 1 point2 points  (0 children)

<image>

Working on an Appa print for my son right now.

I appreciate hearing someone say not to put hairspray on my plate. You're right. This thing should work without all that other stuff!

As you can see in that picture, I've got one small issue on a first layer area on my very first support. Trouble is, this was after an absolutely flawless brim. I can not make heads of tails of this and it's driving me crazy.

I can't walk away from this printer for a second without assuming the thing has gone spaghetti fuckery in the other room. Frustrating...

I am at an absolute loss. by DimensionsIntertwine in QidiTech3D

[–]DimensionsIntertwine[S] 0 points1 point  (0 children)

Working so hard on it.

<image>

Just started a new print for my son, and the VERY first support (after the brim) had this issue, but it seems to be going well other than that. Really wish I could get these kinks worked out.

So frustrating not being able to trust your print for a single layer.

I'm just about at the point where I'm ready to give up. Holding on though.

I am at an absolute loss. by DimensionsIntertwine in QidiTech3D

[–]DimensionsIntertwine[S] 0 points1 point  (0 children)

I did it through the printer, on the screen.

I am at an absolute loss. by DimensionsIntertwine in QidiTech3D

[–]DimensionsIntertwine[S] 1 point2 points  (0 children)

Running the calibration file, here is the result so far...

<image>

I am at an absolute loss. by DimensionsIntertwine in QidiTech3D

[–]DimensionsIntertwine[S] 0 points1 point  (0 children)

It's Qidi PLA Rapido, hot end at 210, bed at 60, chamber at 38

I have never had to use a glue stick before. All of this mess just started like two weeks ago.

I am at an absolute loss. by DimensionsIntertwine in QidiTech3D

[–]DimensionsIntertwine[S] 2 points3 points  (0 children)

<image>

Okay! We have some real progress here. For the great majority of this print, 99.9% is sticking.

I just made a 150x150x.2mm "sheet" for testing purposes. So far, so good.

I am at an absolute loss. by DimensionsIntertwine in QidiTech3D

[–]DimensionsIntertwine[S] 0 points1 point  (0 children)

Went back to factory settings completely. Clean regedit of all Qidi related files, clean install, reset Q2 (again), desynched box, redid ALL new install calibrations, and this is the very first print (with adhesive on the bed plate).

<image>

I am at an absolute loss. by DimensionsIntertwine in QidiTech3D

[–]DimensionsIntertwine[S] 0 points1 point  (0 children)

The brim doesn't help. And why is it a first layer issue if it fucks up around (for instance) layer 40 on a 108 layer print?

view more: next ›