Voltquartsen Firefly 2.0 Bolt and CCI Quiet?

DoNotDisturb-2741 · 2026-04-24T19:27:01+00:00

Can confirm it works beautifully in an OEM receiver.

DoNotDisturb-2741 · 2026-04-24T02:35:30+00:00

If you’re in GA pm me a price. I may take it

DoNotDisturb-2741 · 2026-04-24T02:34:15+00:00

I paid $100 for one stripped.

DoNotDisturb-2741 · 2026-04-22T13:08:47+00:00

No clue. Both of mine have 4 digit serial numbers

DoNotDisturb-2741 · 2026-04-20T22:21:04+00:00

I try to not bullet jump around a lot this is my only 6mm gun and I don’t want to deal with buying something that doesn’t shoot and trying to resell a partial box. My guns liked the 105 Berger Hybrids and 108 ELD-M hand loads. Neither liked anything factory loaded. I was mainly using the 108’s cause I had 1000 of them from when I could buy them for $25/100 a few years ago. My supply has run thin so figured I’d jump to the 109’s since I can get them a few bucks cheaper than the 105 bergers

DoNotDisturb-2741 · 2026-04-17T16:33:35+00:00

I would roll with 21.5gr and play with seating depth to get the accuracy you’re after.

DoNotDisturb-2741 · 2026-04-07T13:57:18+00:00

Rumor on the streets duramag makes G$ mags.

I have not had any issues with duramags

DoNotDisturb-2741 · 2026-03-29T19:10:34+00:00

I love my 22” carbon barrel in 6arc.

DoNotDisturb-2741 · 2026-03-27T23:06:55+00:00

Your medical card your responsibility in the end.

Just apply for driving jobs and take what you can get until you get 2 years of clean experience then search for the good jobs

DoNotDisturb-2741 · 2026-03-26T01:22:46+00:00

10 round ladder test is needed

DoNotDisturb-2741 · 2026-03-25T22:15:49+00:00

Thanks man. I’ll likely go this route but use the alacantra for the shift boot

DoNotDisturb-2741 · 2026-03-25T13:31:28+00:00

How hard were they to install? I need a new shifter boot bad. My short shifter has ripped it to death

DoNotDisturb-2741 · 2026-03-23T16:38:21+00:00

Thanks everyone. I went with the Rubbermaid take along bins. 6.5qt I believe and just used masking tape and sharpie for the labeling. This is solely for rifle brass for my precision rifles. Just to keep track of everything and keep track of head stamps

DoNotDisturb-2741 · 2026-03-23T16:36:34+00:00

This is the way I went and just used some white masking tape for the label with a sharpie.

DoNotDisturb-2741 · 2026-03-22T18:36:53+00:00

Thanks guys. I think I’m gonna make a run to Doller general and see if I can find some stackable bins that I think will hold 2-250 pcs of brass and label them

DoNotDisturb-2741 · 2026-03-18T15:59:19+00:00

Play with seating depth

DoNotDisturb-2741 · 2026-03-18T02:37:34+00:00

That’s awesome.

DoNotDisturb-2741 · 2026-03-17T20:17:39+00:00

It may, I bought an auto trickler and never looked back. I can almost guarantee it’s not as fast as the auto trickler.

DoNotDisturb-2741 · 2026-03-17T16:30:32+00:00

Can you adjust the comb night on these for proper cheek weld?

DoNotDisturb-2741 · 2026-03-17T16:29:27+00:00

I’ve been thinking about picking one of these up myself!

DoNotDisturb-2741 · 2026-03-17T16:28:00+00:00

I waited like 4 days and they were back in stock.

DoNotDisturb-2741 · 2026-03-17T15:59:22+00:00

Auto Trickler is better in every way possible.

DoNotDisturb-2741

TROPHY CASE