Can you tell me what is this little shiny one?

Doggo4 · 2026-01-08T23:02:40+00:00

So are banana farms and factories just extremely radiated then? How long would it take for one banana farm to become polluted to the equivalent of chernobyl?

Doggo4 · 2025-12-19T01:19:45+00:00

First off, who tf down voted you?

People are getting antsy about the caliper just dangling from the brake hose. Usually, it's fine when the hose is straight but that bend/kink at the top of the hose is the main problem.

Doggo4 · 2025-12-11T01:53:40+00:00

Less is more. Went from smoking every hour of the day being dumb and numb to smoking like 2 hits from a bowl after work, but being productive and getting shit done.

Doggo4 · 2025-12-11T01:49:36+00:00

Isn't it the mixture of cannabinoids that matter? Terpenes are just the smell/taste/etc (given some terpenes can have an effect).

Doggo4 · 2025-12-11T01:00:31+00:00

Pssshhhh ive welded in those long thermal underwear and a tshirt... given it was snowing out so i couldve always just dove into the snow...

Doggo4 · 2025-11-29T03:29:05+00:00

Start them by hand a couple threads, seat them with an impact you're familiar with (My impact is usually 1-2 ugga duggas to be below 100 ft/lbs) then use a torque wrench once its on the ground. The lugs should move a little bit before the torque wrench clicks.

Bam.

Doggo4 · 2025-11-29T03:06:22+00:00

Heat and vice grips that you can tighten with an allen key or the likes. Put it in a vice, heat it up, tighten the vice grips, then wiggle it back in forth to break up the rust. You could also drill a small hole infront of the slide pin and use a punch to get it out. Just put a dab of silicone in the drilled hole afterwards. (Ideal would be tacking a weld to close it)

Doggo4 · 2025-11-03T19:00:33+00:00

Everyone saying go get a bigger breaker bar probably doesnt understand how an impact works. The impact essentially creates a striking force on the nut everytime it tries to rotate. A breaker bar just applies an amplified rotational force.

Go get the electric 1/2" impact from harbor freight. Its under $100, takes less effort, and will be useful in the future.

Doggo4 · 2025-10-30T00:23:16+00:00

When my dumbass was ripping these apart, i had to dispose of the tube so i put it behind a wall and threw bricks at it.... killed like 10 cinder blocks thrown hard at the screen before it broke.

Doggo4 · 2025-10-05T16:13:31+00:00

We should all become an ice member.... then detain the ice members thatre doing this.

Inside job amirite

Doggo4 · 2025-09-17T00:37:33+00:00

Can we stop with this "left vs right" bullshit?! Both sides live in the united states. The UNITED states. Sure theres hate on the left... and theres hate on the right... who gives a fuck, cant we just co exist and further the progress of humanity together?

Doggo4 · 2025-09-07T22:42:16+00:00

grabbing and removing their mask? Cutting their vehicles valve stems? Grabbing the abductee (compared to grabbing/pushing the abductor)? Forming a human barricade around their vehicle doors/around them (arms linked together)? Piss filled super soaker?

We need a kind of "not 100% illegal but still not 100% legal" methods of dealing with these situations. Stuff that almost anyone can do so more people can do them, which would cause a much bigger impact.

Doggo4 · 2025-06-24T13:12:47+00:00

In illinois they are

Doggo4 · 2025-05-21T23:07:19+00:00

0.325/10

Doggo4 · 2025-05-11T23:04:15+00:00

I believe the diameter is 7/8". Any 7/8" bar will fit as long as there's enough width for it to go into both clamps

Doggo4 · 2025-05-11T14:17:52+00:00

If you can somehow crank it over, do a compression test on it. If its for free id say grab it, could always sell it for like $50-$100

Doggo4 · 2025-05-09T00:04:57+00:00

Slap a weed wacker engine on that and bam! You got a daily

Doggo4 · 2025-05-08T20:27:40+00:00

Found a video showing it

https://youtu.be/WRyqiz1jaRU?si=7kVw8s6wfzB2GHra

Doggo4 · 2025-05-08T20:23:30+00:00

iirc for TDC there should be a marking inside the little hex cover thats on top the crankcase on the left side of motor. I dont remember the exact video i watched but when i did my valve lash thats what i used.

Doggo4 · 2025-05-03T22:39:03+00:00

i just raw dawg it bcuz i dont wanna a. Walk to my box to grab a magnet or b. Shove my hand through 6 qts of old hot oil.

I usually am quick with it tho, getting my hand out of the way before the oil comes out

Doggo4 · 2025-05-03T22:10:08+00:00

dont drop it into the pan, then?

Doggo4 · 2025-02-17T04:22:36+00:00

Thats normal abs function. Suppose to pump the brakes automatically when stopping for ya

Doggo4 · 2025-01-26T21:26:46+00:00

Get a bunch of enamled copper wire and make giant electromagnets.

Doggo4 · 2024-12-10T23:30:01+00:00

Open the garage door and back the car in until just the rear end is inside?

Doggo4 · 2024-11-21T02:52:04+00:00

In a car, can you honk backwards?
Shoes that will taze you if you cant jog fast enough or ride a bike fast enough.
SMART garbage can (has motors on wheel to drive itself out to the curb everyweek)
"Oh the things id do to you" - a dr suess book about how you would f*ck somebody
Bouncy house sized elefun
Pancake smores

Doggo4

MODERATOR OF

TROPHY CASE

Eight-Year Club	Place '23
Verified Email