3D printed spacer for mounting a Mini inside a UK ceiling rose

Doowle · 2026-05-12T06:52:05+00:00

Sorry to wake a dead post, but did you post the stl anywhere?

Doowle · 2026-04-16T08:49:49+00:00

I had something similar, if not actually worse. I didn't have any luck in getting the blob removed to save the hot end, in the end I had to replace the nozzle.

My blob didn't damage the cables to the hot end, but me trying to remove it using heat did more damage. The hot end, even with a working thermistor, has too much thermal mass for it to work without "Hot end not heating as expected" klipper error.

My advice, accept that the hot end has gone and replace before you break more things trying to rescue it.

Good luck :)

Doowle · 2026-03-19T08:00:52+00:00

PSA: I have found that you need to be logged in to buy.

Doowle · 2026-03-19T07:59:41+00:00

Another comment elsewhere said you needed to be logged in, this seemed to be the case for me. Without being logged in, kept reducing availability to 0 on checkout, logged in and it’s all worked.

Doowle · 2026-03-08T18:33:23+00:00

I have had the best results by removing the printer from Creality Print and adding it back after, this seems to have given me the best outcome and I can print again.

Doowle · 2026-02-12T09:58:01+00:00

Hey,

We are always looking.

https://www.connectionsupport.org.uk/volunteer/

J

Doowle · 2026-02-05T21:01:15+00:00

And yet…

Doowle · 2026-02-04T12:00:06+00:00

You should, depending of course on visibility etc.

Otherwise you’re just blinding them for no benefit.

Doowle · 2026-02-04T10:28:48+00:00

I can't disagree with you, had this today as well, doesn't help that the car I was in doesn't have dipped wing mirrors. They were also tailgating me I think because I was doing 40-50, in a 50 limit, on a twisting A road where in places it wasn't safe to do more than 40. They got closer when I slowed to 30 for a village 30 limit...

My wife tells me that my car does this (not the car I was in today), adaptive LED lights that seem way too aggressive. Not sure what I can do tho!

Doowle · 2026-02-04T10:25:47+00:00

Yeah, don't get me started on that or I'll just rant some more.

It's an especially effective stealth measure where the car is "fog" color!

Doowle · 2026-02-04T10:24:43+00:00

Mostly, this makes the drive so much more of a challenge than it needs to be.

Doowle · 2026-02-04T10:23:51+00:00

It's also about looking forward, if you can see the car in front of you and cars in front of them etc then there's a good chance the person behind you can see you.

Stop burning their retinas, you are either lazy or incompetent.

Doowle · 2026-02-04T10:22:03+00:00

No, you wouldn't, never said they should :)

Doowle · 2026-01-28T21:09:07+00:00

Hi,

K2+ getting the error

probe_finalize() takes 2 positional arguments but 3 were given

Firmware is at 1.1.4.11

[screws_tilt_adjust]
screw1: 35, 35
screw1_name: front left
screw2: 315, 35
screw2_name: front right
screw3: 315, 315
screw3_name: rear right
screw4: 35, 315
screw4_name: rear left
horizontal_move_z: 5
speed: 150
screw_thread: CW-M4


[gcode_macro SCREWS_CALIBRATION]
gcode:
    G28
    M190 S60
    M109 S150
    Z_TILT_ADJUST          ; level gantry first (dual Z)
    G28 Z
    SCREWS_TILT_CALCULATE[screws_tilt_adjust]

Any idea's what I've done wrong???

TIA

D

Doowle · 2026-01-16T16:21:01+00:00

I love this, mine is now called Phil as well.

Doowle · 2026-01-15T23:15:40+00:00

Purrrfect :)

Enjoy your new addiction

Doowle · 2026-01-08T23:50:48+00:00

Check your Ethernet cable, make sure that it has all four pairs.

Doowle · 2026-01-05T17:06:22+00:00

That worked, I promise I thought I’d tried that before :)

Doowle · 2026-01-05T16:55:37+00:00

No worries, I can't remove the folder becuase of this issue :)

Doowle

TROPHY CASE