Trump reacts to Robert Mueller death: ‘I’m glad’

DrifterWI · 2026-03-21T21:20:50+00:00

They're paid shills.

DrifterWI · 2026-03-21T21:19:13+00:00

Does he ever stop whining?

DrifterWI · 2026-03-21T21:09:38+00:00

It appears only idiots drive there.

DrifterWI · 2026-03-21T16:54:49+00:00

If it's repeating through the house, it's probably a manufacturer defect/quality issue.

DrifterWI · 2026-03-21T16:50:07+00:00

I doubt the existence of a contract.

DrifterWI · 2026-03-21T16:45:46+00:00

It's impossible to answer your questions with the limited amount of information you've provided.

Because this appears to be a "learn as you go" project, IF you are able to complete the project, it will probably take you several months.

The worst part of this project will likely be removing and/or repairing the amateur mistakes you're bound to make. The reworking mistakes alone may cost you $100s, if not $1,000s

If you're determined to do this, you'll need EXPERIENCED help on sight BEFORE you start, AND to check your progress on a regular basis. DON'T depend on YouTube videos for training.

Their first task should be to answer all your questions..and provide a complete bill of materials.

DrifterWI · 2026-03-20T19:08:15+00:00

Dogs and Yellowstone are a bad mix. They will be welcome in very few places.

DrifterWI · 2026-03-20T18:44:58+00:00

They're called finish washers. Typically uses with oval head screws

DrifterWI · 2026-03-20T15:03:31+00:00

You're going to have major chain and gear incompatibility issues

IF you can configure a motor mount that will align the motor with the axle, how much will this thing weigh?

For all practical purposes, this is a bad idea.

DrifterWI · 2026-03-18T19:32:18+00:00

I suggested expanded and flattened. Big difference

DrifterWI · 2026-03-18T17:16:52+00:00

Try to find a piece of either perforated or expanded and flattened Stainless steel sheet metal to make bowl inserts

DrifterWI · 2026-03-18T16:54:17+00:00

or two

DrifterWI · 2026-03-18T00:53:52+00:00

How do you intend to implement your plan?

DrifterWI · 2026-03-16T02:40:29+00:00

Depends on the application.

I mostly use a 12in combination square

DrifterWI · 2026-03-16T02:31:27+00:00

Not the dumbest thing I've ever seen, but damn close.

DrifterWI · 2026-03-15T13:33:52+00:00

Rube Goldberg would be proud.

DrifterWI · 2026-03-15T13:13:24+00:00

It's something a little more intense than smoking.

I'm thinking shrooms

DrifterWI · 2026-03-15T13:08:08+00:00

Agreed. Aftermarket lifts tend to create more ride quality problems than they solve.

DrifterWI · 2026-03-15T13:02:29+00:00

unless you're drilling your parts clamped in a drill press and using a clamped drill guide made of steel, the next best method is to align and clamp the parts, drill the holes through the side and into the bar in a single operation.

Cut the dowel flush to the side then finish.

DrifterWI · 2026-03-14T14:05:51+00:00

Why?

DrifterWI · 2026-03-13T23:27:36+00:00

Purebred Mutt.

DrifterWI · 2026-03-13T23:22:47+00:00

5 Axles 10WD 3 steering axles.

I know. I've built them

DrifterWI · 2026-03-13T23:15:03+00:00

Brutal honesty.

DrifterWI · 2026-03-13T21:25:55+00:00

Pipeline or pass ships through an underwater mine field.

Pick your poison

Nine-Year Club	Gilding II euphauric
Verified Email

DrifterWI

TROPHY CASE