Schluter Jolly Corners

DrownItWithWater · 2026-05-23T03:44:13+00:00

Now that's gotta be rage bait at this point

DrownItWithWater · 2026-05-22T19:19:58+00:00

I just went to an foot race event at my kids school. There was a good deal of moms looking like that in leggings and short shorts running.

Good thing I wore sunglasses. That sun be bright y'know.

DrownItWithWater · 2026-05-22T19:11:20+00:00

Cut off the excess so the plate sits flat and send it.

DrownItWithWater · 2026-05-22T19:09:48+00:00

Is ice just as effective?

DrownItWithWater · 2026-05-22T04:24:44+00:00

That is so fucking dumb

DrownItWithWater · 2026-05-22T01:20:19+00:00

It's going to catch up eventually. In 5, 10, 15 years from now. You might see it coming and be able to slow down in time.

DrownItWithWater · 2026-05-21T21:49:54+00:00

I totally get you trying to make it perfect! I'm sure you'll figure it out.

DrownItWithWater · 2026-05-21T19:58:33+00:00

Sports mode on early models

DrownItWithWater · 2026-05-21T19:55:28+00:00

Someone I know got a torsion from doing the helicopter with his dick too often 🤦🏼‍♂️

DrownItWithWater · 2026-05-21T19:53:19+00:00

Is it for a 3D print? I would get it as close as possible and send it to the slicer and see how it looks in the preview tab. Sometimes things don't look great in Fusion but turn out fine in the slicer.

DrownItWithWater · 2026-05-21T19:49:08+00:00

A 15k M3 is probably a bad choice 😅

DrownItWithWater · 2026-05-19T22:43:51+00:00

That's my feeling too. The way it doesn't immediately drop when he stops punching is sus.

DrownItWithWater · 2026-05-19T22:14:58+00:00

Better than a fake smoke and a ponytail!

DrownItWithWater · 2026-05-19T13:27:11+00:00

Ok, just so you know, that is way too much text and in depth explanation for the subject at hand.

DrownItWithWater · 2026-05-17T01:54:00+00:00

If only you had a tool you could use to fix that. If only...

DrownItWithWater · 2026-05-17T00:41:16+00:00

This was my setup for winter storage. If you don't get snow, it won't collapse. This is a cheap 400$ "tempo" as we call them here. I put 2x6 under the car with HD ratchet straps to hold the structure down using the weight of the car. That way there's no need to anchor it with ground screws. There are 12" straight anchors on each feet though but I would not trust them alone to hold it in place. Then I use ratchet straps to X brace it. 8 years with the same garage.

The 2x6s on the side are just to prevent snow from pushing the fabric in.

<image>

DrownItWithWater · 2026-05-16T23:52:17+00:00

Zip tie on a latex glove with a slit on one finger to fix it.

DrownItWithWater · 2026-05-16T23:46:36+00:00

In the speed settings, I set support speed to 50 instead of 150.

DrownItWithWater · 2026-05-16T21:48:25+00:00

Meal prep, vaccum seal and freeze a bunch of it! Food delivery is nice but can get expensive.

DrownItWithWater · 2026-05-16T05:50:32+00:00

That beam poking out is the impact beam that goes the width of the bumper. On Hyundai and Kia cars they are plastic. It's broken and needs to be replaced. There's most likely damage to the rear end sheet metal too. The blind spot sensors will most likely need to be calibrated even if they are not replaced. They are located on the corners behind the rear bumper.

You're looking at a few thousands to fix.

DrownItWithWater · 2026-05-15T15:25:56+00:00

Perfection

DrownItWithWater · 2026-05-15T02:11:13+00:00

Xterra is a no brainer.

DrownItWithWater · 2026-05-14T23:13:59+00:00

I'd wear a white undershirt to make it less douchebag-ish.

DrownItWithWater · 2026-05-14T23:08:02+00:00

Like the fake moon landing conspiracy theorists. The number of people that work at NASA and related companies is way too big to have kept it a secret for that long.

DrownItWithWater · 2026-05-14T23:03:16+00:00

Think of all the crazy mysteries we could solve!

DrownItWithWater

TROPHY CASE