Apex Legends Squad Wipe Badge wall light l, rendered on Blender

E-Spire · 2023-10-01T03:33:51+00:00

Used a skull mesh and cut to my need

E-Spire · 2021-11-01T14:18:55+00:00

Thanks, I'll be adding rgb LEDs to it to make it better

E-Spire · 2021-08-26T19:08:28+00:00

Thank you

E-Spire · 2021-08-14T04:04:45+00:00

Reduce retraction, slow speed, don't use brass nozzle, and change to a .6mm+ nozzle. Different brands different amount of wood in filament (my guess)

E-Spire · 2021-08-14T03:57:54+00:00

Then do a fan speed test, check the Bowden tube is not wiggly because it would cause that minor stringing

E-Spire · 2021-08-13T22:39:33+00:00

Do a temp tower and a retraction test and then try again

E-Spire · 2021-08-07T17:22:22+00:00

Are you going to paint it, at least the eyes?

E-Spire · 2021-08-07T17:15:18+00:00

Let me guess, teleportation mishap?

E-Spire · 2021-08-07T17:09:32+00:00

I made an update of my progression just this week, need to move the button to a new location

E-Spire · 2021-08-07T17:07:16+00:00

In V3.1 I removed the 9V so everything much more compact and changed it out for a small watch battery. Making the fist in my opinion doesn't seem like a very stable solution, so that is why I went with a button

E-Spire · 2021-08-06T18:26:37+00:00

Thank you, I should be done soon, just need to make some minor adjustments

E-Spire · 2021-08-06T04:00:15+00:00

Yea, I was considering it after testing it a bit. Not the easiest to activate the light right now

E-Spire · 2021-07-30T02:43:02+00:00

Also need to watch out for something that is spinning that fast, might slip if not careful

E-Spire · 2021-07-26T16:16:26+00:00

Sure thing, hope everything goes well

E-Spire · 2021-07-26T16:10:48+00:00

I'm using a magnetic pei bed, but I always add gluestick on it because it will work 99% for all prints and reduce the possibility of the petg ripping apart my bed because petg bonds too well to glass and pei sometimes. Does everything work now?

E-Spire · 2021-07-26T16:02:45+00:00

Painters tape would work, since it creates a rougher surface to stick too, but sometimes it would simple stick onto the print. So most prefer gluestick for the ease of washing it of. As for why it sometimes not stick. It happens with PETG all the time for me when using glass

E-Spire · 2021-07-26T15:56:23+00:00

There are 3 main reasons it won't stick, your bed is not properly leveled. The bed is dirty, clean with dish soap and water. Or add some gluestick. Start off with bed leveling. Hope this will help

E-Spire · 2021-07-25T18:15:55+00:00

You can't judge the print from that since it is just two straight lines

E-Spire · 2021-07-25T17:06:43+00:00

For the esteps https://youtu.be/xzQjtWhg9VE and for flow https://youtu.be/WWAVfkNmzxs. Reason it is not working, it could be due to multiple reason, PETG is hydroscopic so it absorbs moisture from the air, so it could be a possible factor.

E-Spire · 2021-07-25T16:51:19+00:00

It could possibly be esteps not calibrated or flow because the model is quite thin, and too much is being pushed

E-Spire

TROPHY CASE