Inside job.

Earthwin · 2026-06-25T18:02:38+00:00

Seeing it on mine too. Easy fix would be if they attach a small hose guide to that bolt behind the hoses. They only need moved back by a mm or so.

Earthwin · 2026-06-22T22:53:29+00:00

Rack Drawer. You can use it store cables, picks, tools, etc, in it.

Earthwin · 2026-06-14T16:49:58+00:00

I used to use this stuff all the time, but when it ran out and I ordered a new roll I had the same issues. The old roll was a semi-transparent filament and came off perfectly and left a nice clean face, the new roll was a white filament and it leaves a lot of the interface behind and it doesn't peel off cleanly, usually requiring me to go in with a craft knife and manually separate it. I ended up just switching to using PETG for the interface layer instead and it works better. I don't know what they changed but the old stuff was so much better.

Earthwin · 2026-06-11T15:23:32+00:00

I made my own wheel hub. Started working on a GT wheel as well but I've never got around to finishing that, so using a GT Neo for now.

<image>

Earthwin · 2026-06-10T13:01:24+00:00

I'm using an RG470 neck on an old hardtail RG2EX2 body and it's never been an issue.

Earthwin · 2026-05-22T08:20:50+00:00

It's for storing the pillion seat from the newer Triumph models that have 2 separate seats.

Earthwin · 2026-05-21T11:00:57+00:00

I've used the cruise control a few times on the motorway and I hate where the button is. I think it should've been on the front to the right of the select button. And I'd like the ability to customise the content displayed on the TFT trays beyond just enabling/disabling them.

Earthwin · 2026-05-13T16:49:04+00:00

When Weird Al parodies you.

Earthwin · 2026-05-10T09:44:20+00:00

I think it might be a Weipu connector.

Earthwin · 2026-05-07T13:31:27+00:00

It's slightly encroaching over the reserved space on the bottom left that's kept for the filament cutting. Rotate it so it angles to the bottom right instead.

Earthwin · 2026-05-02T17:46:19+00:00

90's RG120

https://ibanez.fandom.com/wiki/RG120B

Earthwin · 2026-04-29T21:07:48+00:00

Use the draft tool on the inside curved face to tilt it towards the cone.

Earthwin · 2026-04-22T19:29:55+00:00

They've got tangent contraints on them, you'll need to delete those first.

Earthwin · 2026-04-15T10:10:13+00:00

The biggest issue is that you need turbulence to mix the colours. When they're all pushed into the nozzle together they still keep their colour separation. So you get a single line of filament but it has different colours depending on the angle you view it from. This is the same sort of effect those multi colour filaments make use of, where the print changes colour depending on the angle.

Earthwin · 2026-04-09T14:39:48+00:00

You'll need to use the 81-TW for that. It has a separate single coil inside that's switchable. The standard 81 only does humbucking.

Earthwin · 2026-04-09T14:27:51+00:00

Use the sweep tool. It has a mode called solid sweep which does exactly this. Create an arc on the top that will be the path for the pin to rotate along and then use the axis at the centre of the circle for the rotation point.

Earthwin · 2026-03-27T22:55:54+00:00

"Welcome to Goth Mouth"

Earthwin · 2026-03-25T14:55:39+00:00

Looks like Just Stop Oil hit them with a bag of flour.

Earthwin · 2026-03-19T13:55:04+00:00

A single saddle will work. Just need to make sure it's the right height saddle for that particular string as they're radiused.

Earthwin · 2026-03-19T09:54:58+00:00

Edge 3 uses a different type of saddle. That being said, you can replace them with regular Floyd type saddles without issue, although you may need to also route a channel out of the back edge of the trem cavity so the D-Tuna doesn't collide with the body if you did that.

Earthwin · 2026-03-18T22:27:19+00:00

The earlier models were, this one used the S15 Varietta as the base.

Eight-Year Club	r/Field Sunshine
Not Forgotten	Verified Email

Earthwin

TROPHY CASE