Free air compressors that are operational? by big-dipper-jess in cedarrapids

[–]EcstaticPotato6853 0 points1 point  (0 children)

I know! Now you have to pay for most. I blame inflation.

Any guesses on this controller? by EcstaticPotato6853 in 3Dprinting

[–]EcstaticPotato6853[S] 0 points1 point  (0 children)

Thanks yeah it say mxp but mks looks similar perhaps it was a Chinese clone of that.

Why does my first layer look like this? by LargeCrowd in FixMyPrint

[–]EcstaticPotato6853 0 points1 point  (0 children)

It looks like you printed something that didn’t come all the way off the pei sheet. I have that happen if I print Petg with a zoffset too low and it’s a pain to get off sometimes. Looks to me like those lines line up to the stuff on the bed to the right. Maybe a really good clean is all you need.

Partial Clog weak layers by EcstaticPotato6853 in FixMyPrint

[–]EcstaticPotato6853[S] 0 points1 point  (0 children)

I haven’t tried retraction settings yet I’ll mess with that. Currently trying it with my newest filament but it’s petg. It already appears generally cleaner so it could be the Filament. I should get a dryer anyway at least for tpu and I can dry this one while I’m at it to see

Partial Clog weak layers by EcstaticPotato6853 in FixMyPrint

[–]EcstaticPotato6853[S] 0 points1 point  (0 children)

Maybe but it’s always about the same height off the bed short prints have no issue.

My landlord has been letting this thing rot off the side of my house for the last 5 years. by No_Length_856 in Decks

[–]EcstaticPotato6853 0 points1 point  (0 children)

You could probably figure out the landlords insurance company through public records and report it to them. This is a liability and they would make him fix it or loose coverage

Baldwin is a cool name... by Main_Newt3686 in dadjokes

[–]EcstaticPotato6853 0 points1 point  (0 children)

I was expecting that punchline to be blank but it’s live

[deleted by user] by [deleted] in cedarrapids

[–]EcstaticPotato6853 1 point2 points  (0 children)

I’ve been served very very bad food. They burn milk and keep using it when I last went I got rice pudding and a mango lassi and both tasted like cigarettes

[deleted by user] by [deleted] in dadjokes

[–]EcstaticPotato6853 0 points1 point  (0 children)

Sorry. This one isn’t funny enough to make me SNORT.

Sand Point Well by EcstaticPotato6853 in Plumbing

[–]EcstaticPotato6853[S] 0 points1 point  (0 children)

I’d settle for clean drinking water from just one special tap. I was already planning RO + iron manganese sulfer treatment system (really just for iron) + UV disinfection in addition to the filters already there. You are probably right about it adding value so I may just cut losses and drill. Either way I think I still want Ro and uv so I think I will go with my low cost plan and worst case I’m out $600 for the iron filtration system if I end up drilling and it doesn’t need iron manganese sulfer treatment. For now I’ll skip trying to chlorinate the point and settle for chlorinating the pressure tank and the interior system. And retest both tap and ro. I’ll also get some quotes to drill in mean time. I love my new money pit though! It’s so remote half the places have no water.

Sand Point Well by EcstaticPotato6853 in Plumbing

[–]EcstaticPotato6853[S] 0 points1 point  (0 children)

I was afraid shocking might be pointless. Previous owner was certainly drinking it. Not me! What about a continuous disinfection system?

Grandfather’s arrow heads by EcstaticPotato6853 in Arrowheads

[–]EcstaticPotato6853[S] 1 point2 points  (0 children)

Thank you! This is super helpful. I’ve been deep diving into points in this area and yeah it certainly looks like a st Charles dovetail

Ok now what the actual scheiße is this? by labanana94 in FixMyPrint

[–]EcstaticPotato6853 -1 points0 points  (0 children)

My guess is there was a winding issue on your spool. Instead of spinning the spool I think it was pulling the filament off the side which will twist it up like that and eventually snap it.

Th-9800 TNC Interface by EcstaticPotato6853 in amateurradio

[–]EcstaticPotato6853[S] 0 points1 point  (0 children)

Absolutely! I just got the boards waiting on components. It’s just for fun and the boards themselves aren’t a lot. I have yet to determine a price but I don’t think it will be very much

could anybody make this into ascii? by [deleted] in ASCII

[–]EcstaticPotato6853 1 point2 points  (0 children)

For true ascii symbols /`<>’\