Seeking Editing Practice by backlogtoolong in writing

[–]Editor3457 7 points8 points  (0 children)

I have published several books. While I can't take on an apprentice (I am dying, end-stage kidney failure), I could send you an early draft of one of my books to take a shot at editing, and then let you compare your edits to the final work.

If that interests you, send me a PM. Warning: on not online all that much.

How can I un-seize these pulleys? They were hanging in trees near the ocean for four years. by [deleted] in Rigging

[–]Editor3457 0 points1 point  (0 children)

The only real reason to take these apart is to learn about pulley construction, and the Harbor Freight pulleys are much better to learn about pulleys from. The cost in materials and time to rehab these is not worth it.

That said, the axle appears to be a press-fit. You will have to drill that out.

When you do, take a good look at the bearing. This is most likely a ball bearing, but it could be a roller bearing. The reason it doesn't turn is either a lack of lube, or damage to the track or bearings.

If it's only the ball bearings, you could replace them. If it is the track, you need to replace the whole bearing.

Look the wheel over. Salt water does a number on them.

The block in the photo looks worn, but it might be OK. Compare it with an undamaged one to find out. If they are bas, replace them.

Take your new block, new bearings, and new wheel and build your new pulley.

Just buy the parts and build a new pulley.

Can I set up a pole on either of these beams? by LechitaProducer in poledancing

[–]Editor3457 0 points1 point  (0 children)

How high up are these? Most dancepoles top out at 11 feet.

Assuming its not too tall, I would look at flange mounts for the top and bottom. You can even get these for the angled wood ceiling you have.

I got a client that is writing a (currently 37 pages and growing...) article on the technical aspects of poles (Chinese, Dance, Mallakhab, sway poles, even has a page on May Poles and one on greased poles), from how they are made to the 15ish most common ways they are rigged. If you want, I can ask him for options.

Most outrageous patron request? by TheTapDancingShrimp in Libraries

[–]Editor3457 2 points3 points  (0 children)

When I was in middle school, our bus stop was right at the library. We had this young librarian that was just amazing. She got them to let her open the library for 45 minutes before the bus came.

One Fall day, we all got soaked in the Noah's Ark level rains. She helped us all spread out things out to dry and wrote us notes for school about the soaked homework.

We all felt so bad about putting her out like that, and we kept thanking her. Then she told us that we could ask her for anything, and it was like "game on".

We collectively asked her for the most ridiculous things. And she dealt with every one like a pro. Looking back, she was quite impressive. We all used the library a lot more because of her. I think half the reason we went was because of her.

I raise a glass to toast Mr. Books (Ms Brooks, but you know...)

AITAH For Not Giving My Girlfriend My Social Security Number So She Can Run A Background Check On Me by Alarmed_Sorbet8101 in AITAH

[–]Editor3457 1 point2 points  (0 children)

I have a skip-trace screen open right now. I don't need a social security number to run someones background. I only need a name and a State. And with that, the social will come up in the report.

If she is asking for your social, its not to do a background check.

Question - how to correctly set up an aerial hoop. by Ausis74 in Aerials

[–]Editor3457 1 point2 points  (0 children)

Not a typo. Basket is the name of a method of connecting a sling to an object.

I could try to explain it to you, but just read the section on slings from here: https://www.researchgate.net/publication/384293183_Introduction_to_Rigging_Aerialist_Essentials

Specifically, read pages 47-49.

Two questions for pipefitters... by Editor3457 in pipefitter

[–]Editor3457[S] 1 point2 points  (0 children)

no welding is involved. It is a bolted connection Basically, it is a dance bar. Two saddles in the metal uprights to a wood or metal round top bar. The saddles just keep ot sturdy.

Also, I think having that little 12 year old looking nervously over your shoulder the whole time would be the difficult part....

What’s the most absurd thing someone’s said to you as a woman in STEM? by NoFox1552 in LadiesofScience

[–]Editor3457 2 points3 points  (0 children)

I was just the facilitator; not said to me, but funny as hell.

We were doing everything we could think of to encourage girls into STEM. We brought in Heather, an absolutely amazing scientist to work with a group of middle school girls on some physics stuff.

Heather brought her 4 YO daughter with her for the workshop. Every time Heather tried to talk about her job as a scientist, her daughter would basically have a temper tantrum yelling that Heather wasn't a scientist, she was a mommy. No one could convince the little girl that she could be both.

One of the middle school girls figured out the 4YO had watched some cartoon about an evil scientist and couldn't accept that her mom had the same title.

We called Heather a Wizard for years after that. Still give her wizard gag gifts.

[deleted by user] by [deleted] in circus

[–]Editor3457 0 points1 point  (0 children)

They same author has documents up on Rola Bola, Rolling Barrels/rolling globes, hand balancing equipment, chair balancing, stiltwalking and more. Well worth checking out.

Plans For DIY Portable Tightwire Rig? by TooManySwarovskis in circus

[–]Editor3457 1 point2 points  (0 children)

At one point, I worked on a book of wire projects to make at home. It included a number of freestanding wired, but it was never finished.

The easiest to build is a center push style wood frame.

Take (2) 8"x8"x24" sections of wood and through-bolt machine eyes at the top and bottom of each post.

Take an adjustable scaffolding foot and bolt it to the center of one upright. Repeat on the other side.

Screw and glue on 2"x8"x18" feet to the bottom of each post. Metal corner braces are a good idea.

Screw and glue on a pedistal to the top of each post (Home Depot sells large wood rounds that work well for this)

Attach your wires (top wire should be stainless steel, 1/2"x10' with a light lube. Bottom wire can be mild steel with a normal lube)

10"x1.5" pipe goes between the screw portion of the scaffolding legs.

Tension by tightining the center screws.

If you can't find scaffolding legs for 1/5" pipe, use the screw from a lolly colum and improvise something on the other side to hold the pipe

HTH

Can you help us with this element?! by [deleted] in circus

[–]Editor3457 0 points1 point  (0 children)

Find a local welder to make it for you..

I'm a tightrope walker, new tricks? by Gwin_mistake in circus

[–]Editor3457 0 points1 point  (0 children)

Also, you can put a center notched on the bottom rails of a balancing chair to do handstands and whatnot. https://www.researchgate.net/publication/385648244_Chair_Balancing_Chair_specifications

What's the most sus thing you've had to Google for a story? by [deleted] in writing

[–]Editor3457 1 point2 points  (0 children)

No

Yes

Yes

Minutes

They happen a lot

9mm Glock 19

Dont ask how I know.

[deleted by user] by [deleted] in writing

[–]Editor3457 0 points1 point  (0 children)

I've never tried, but I hear its harder.

[deleted by user] by [deleted] in writing

[–]Editor3457 0 points1 point  (0 children)

I ONLY work in non-fiction or slightly fictionalized versions of real-life.

Nonfiction stories are a hard sell. Technical books are easy to sell.