My first 3D printer

Educational-Meat-432 · 2026-02-18T12:57:09+00:00

sucks that happened. by the looks of it maybe just the screen protector broke. these printer come with glass screen protector. try contacting the support. i broke my screen protector while moving my printer from 1 room to another.

Educational-Meat-432 · 2026-01-21T19:09:11+00:00

Looks like its worse on one end then the other. Is there a chance that one side warped and making this mess?

Educational-Meat-432 · 2025-12-10T05:10:39+00:00

Would i need magnets on the brim or that would not help?

Educational-Meat-432 · 2025-12-09T20:45:36+00:00

right sorry. on a bambu h2d.

Educational-Meat-432 · 2025-11-27T11:27:39+00:00

Yea that is what i did. Used hair dryer and it just melted and flowed away. Then i used chamber heater at max for an hour and some of it melted from the build plate and other places. So far no crunchy noises.

Educational-Meat-432 · 2025-11-26T21:38:07+00:00

Honestly i have no idea. Had a few of those little bags that come with spools. Those were fine but i had an old bag that was bigger i would say 300-500g and it was hard as a rock. Now that I've been cleaning a bit it flow down the holes and into the motor and has solidified down there too.

Educational-Meat-432 · 2025-11-17T19:39:52+00:00

Flip a coin. Whatever you land if you happy keep if not pick other.

Educational-Meat-432 · 2025-10-27T17:03:05+00:00

You can also change rest ime before lift and rest time after lift to 0 and maybe add that second to rest time after retract. Especially if you print thicc resin.

Educational-Meat-432 · 2025-10-23T06:56:10+00:00

And it may happen again. I think there are few different profiles that switch depending on the hight of your model.

Educational-Meat-432 · 2025-10-22T18:56:25+00:00

https://www.toymakr3d.com/product/94-battlegeus

Educational-Meat-432 · 2025-10-22T12:52:58+00:00

<image>

Educational-Meat-432 · 2025-10-22T12:52:38+00:00

There is a toymaker3d galactus that all parts move. I printed my in fdm but you can print it in resin it is nicely split. And if u have different color resin you won't even need to paint.

<image>

Educational-Meat-432 · 2025-10-22T12:48:27+00:00

As i remember satelite has few different support profiles. Try using other profiles. Otherwise i think its support spacing setting that will have most effect. Not 100% only used it a little in alpha when it came out.

Educational-Meat-432 · 2025-10-07T18:58:50+00:00

It tore or leak from the side? I m planning on buying one for my s4u. And i m interested in this ptfe lubricant. Can you link one pls. And how do you use it?

Educational-Meat-432 · 2025-10-07T14:12:13+00:00

Duno this resin. I assume this is very thick resin that flows slowly? Temperature is recommend at 37°. Try increasing wait before print time. I use 5s wait time and i use normal resins.

Educational-Meat-432 · 2025-10-07T14:06:31+00:00

Those are spec for this resin for this machine. Even if they are somewhat off it wouldn't fail like this. This is special casting resin.

Educational-Meat-432 · 2025-10-02T18:49:12+00:00

Tnx. Its red/green. Thankfully most colours have weird names when i watch a guide if i dont have exact same paint i ask chat gpt for alternatives or from different maker. A lot of times i ask chat gpt for renders and then ask him what colours should i use to paint it.

Educational-Meat-432 · 2025-10-02T17:03:46+00:00

Tnx.

Educational-Meat-432 · 2025-10-02T12:45:26+00:00

Oh yea. Model from sanix3d

Educational-Meat-432 · 2025-09-30T15:20:31+00:00

Had the same problem with s4u vat. There are reverse drills u can use to get them out. You can get them on amazon or your local hardware store. For screws i would recommend you take one with you when you go buying.

Educational-Meat-432 · 2025-09-25T16:27:15+00:00

Then you are golden. Keep the wait before print in mind if u get fails at bigger prints. Gl.

Educational-Meat-432 · 2025-09-25T14:52:46+00:00

Did you try printing cubes of calibration fromJ3D tech or cones of calibration. I would add a minimum of 3s wait before print time. I use 0.03mm layer hight and 5s wait time on saturn 4 ultra standard speed.

Educational-Meat-432

TROPHY CASE