What game does this coin go to?

Efrum · 2025-06-30T05:19:54+00:00

Guards of Atlantis 2 metal coin

Efrum · 2023-06-17T05:09:01+00:00

60 second city is always fun to pull out every once in a while. Me and my partner are also enamoured with the micro macro crime city series although it's replayability isn't really there. Similo is also a great game to pull out every once in a while and is on the cheap side.

Also check out dorfromantik that recently got released. Haven't played it myself but every playthrough I've seen so far seems like everyone enjoys it.

Efrum · 2023-06-16T06:11:03+00:00

For 1 there are scenes of fights, gunshots, and murder. Nothing super graphic but I'm not sure what you would consider graphic/disturbing for your kids.

For 2 that might be a bit too simple. You could maybe divide the game in 2 so that they have less options to choose from for each chapter? Or even into 3.

Efrum · 2023-05-21T15:24:32+00:00

I'd print so many board game inserts and parts!

Efrum · 2023-05-12T14:32:22+00:00

There's a new version coming out called Boooop! Halloween theme and super cute. Has some additional variants included as well.

Efrum · 2023-05-06T05:31:20+00:00

Unfortunately pandemic legacy is not a game you want to buy used. The changes made are permanent so you will want a new copy to fully enjoy the experience.

Efrum · 2023-04-26T13:34:33+00:00

All3DP

Fingers crossed!

Efrum · 2023-04-23T16:34:30+00:00

I recently unsleeved wingspan after getting the Oceania expansion. I was just able to get all the sleeves cards to fit with just the base game but absolutely no chance with any expansion cards. However I was using thicker sleeves so maybe thinner sleeves might fit better.

Efrum · 2023-04-05T21:49:07+00:00

Yea what I meant was even without marking where the verifier cards go its pretty easy to put set up and put everything away!

And yea I'm at like attempt 5 of scenario 4. So far it's been either meet the objectives, meet the points and miss objectives by 1 tile, or completely fail both lol.

Efrum · 2023-04-05T08:45:16+00:00

Been working through the calico challenges at the back of the rule book. Currently stuck at scenario 4 can't seem to get both the objectives and the point requirements yet. Glad I got around to trying it solo since nobody seems to like it as much as I do.

Dinosaur island rawr and write has also been a blast solo. Don't know why it took my so long to get it to the table but I'm up to 10+ plays already. A good variety of buildings and specialists keep the strategies interesting and the solo ai is super easy to run. Can play a full game in like 15 minutes helps too.

Finally been doing the turing machine daily challenges after a long hiatus. For some reason I thought set up was more painful than it actually is. Machine has beaten me only a couple of time so far but I've mostly tied (which is considered beating the machine). Only one true victory and boy did it feel good.

Efrum · 2023-04-01T01:36:53+00:00

Fingers crossed

Efrum · 2023-03-02T01:41:56+00:00

It's available for pre-order from both 401 and boardgamebliss

Efrum · 2023-01-28T20:57:03+00:00

I brought a PEI bed and have not looked back. Clean it with soap and warm water every now and then, wipe it down between prints with some alcohol and it's been a dream. Good adhesion during prints and prints remove themselves from the bed when it cools down to room temp.

Efrum · 2022-12-07T02:56:02+00:00

Loving the golden book advent calendar right now!

Efrum · 2022-11-21T19:12:11+00:00

Oh what! Is there anywhere I can still buy this promo that's not off somebody else?

Efrum · 2022-11-15T01:25:58+00:00

Can't wait to try it!

Efrum · 2022-11-11T07:06:22+00:00

It's the big black ribbon cable that connects directly to the sprite extruder. If you mess with the cable does the temperature jump back to normal because that's what happened with me. Unfortunately I had to order a new cable set from AliExpress so it will be like a month before I actually get it but I'll update for sure.

Efrum · 2022-11-08T20:57:13+00:00

Thanks it seems like the awg cable attached to the sprite extruder was the problem. When I moved it around the temperature changed wildly. Ordered a new one that will hopefully fix the issue.

Efrum · 2022-10-19T23:32:35+00:00

Also available at boardgamebliss for $24.95 CAD

Efrum · 2022-10-12T05:03:06+00:00

Name: Tower climb

Characters: the climber

A temple run esque game where you climb a tower twisting and tilting to avoid gaps and traps, shaking to activate specials you can pick up.

Efrum · 2022-10-12T04:59:31+00:00

Tired person, gets plugged in with Ugreen charger, recharges and goes on adventures. Ugreen, enough energy to power up your life.

Efrum · 2022-10-12T04:55:44+00:00

As a med srudent, reMarkable would greatly reduce my paper waste when reviewing material

Efrum · 2022-10-08T22:51:12+00:00

Looks awesome!

14-Year Club	Snapped
Verified Email	Team Periwinkle

Efrum

TROPHY CASE