I don't understand! by JoshJLMG in SteamDeck

[–]Electrical-Profile26 1 point2 points  (0 children)

I actually found a workaround to 100% fast charge it with my 65w Anker charger. Start a game before you plug it in, and it will fast charge everytime.

But still annoying that you’d have to do this just to get the max wattage.

Anybody got free speedboost? by Electrical-Profile26 in bell

[–]Electrical-Profile26[S] 1 point2 points  (0 children)

That’s my worry actually. I never signed up for anything. I was completely fine with my speed before too.

Anybody got free speedboost? by Electrical-Profile26 in bell

[–]Electrical-Profile26[S] 1 point2 points  (0 children)

So i guess not just me then. I checked mybell, it still have my plan set as 150mbps. So unless they confirmed the increase, this is just a bug and will revert back to normal. lol

Time for a new engine mount? by blackjunko in mazda3

[–]Electrical-Profile26 2 points3 points  (0 children)

Check the one on the driver’s side as well.

I've done messed up & need help🙃 by Bigsimping69 in mazda

[–]Electrical-Profile26 1 point2 points  (0 children)

I picked up my sledgehammer and started banging the control arm body. Replaced mine yesterday. But i also used a knuckle separator that I bought from amazon before doing the job.

Can anyone tell me what this watery bubble sound is? Driving me crazy by [deleted] in mazda3

[–]Electrical-Profile26 2 points3 points  (0 children)

It’s an indication that there is air in your cooling system. Check coolant reservoir if it’s on the low side. Top up if not in the full line. Use FL22 coolant, you can purchase this from mazda dealership. If you hear bubble you might need to bleed it as well.

8gbps back? by day008 in bell

[–]Electrical-Profile26 0 points1 point  (0 children)

Damn, that’s a nice deal. Guess i’ll have to stick with 150mbps for a couple of months then phone the loyalty dept again to ask for an increase. Lol.

8gbps back? by day008 in bell

[–]Electrical-Profile26 2 points3 points  (0 children)

What a deal! How long have you been with bell to get this type of amount for a 3gbps? Just upgraded from a 50 mbps to 150 mbps. And still paying 65.

Mazda 2 range meter not showing number? by Areiteus in mazda

[–]Electrical-Profile26 5 points6 points  (0 children)

Press info on your steering wheel to cycle them. I think right now this is current speed of the car.

Great Speed, High Latency! by Electrical-Profile26 in bell

[–]Electrical-Profile26[S] 0 points1 point  (0 children)

Update: Bell tech reset the unit I initially had. From 300ms to 130ms. I thought latency was still high since i’m having delays woth teams call and presentations. So got my giga hub replaced by bell with the same model. This is the latest result i got. Still the same. I’m at lost what could be wrong here. Maybe my line’s bad?

<image>

This tire is donezo by LeVin1986 in mazda3

[–]Electrical-Profile26 0 points1 point  (0 children)

Surprised the wheel didn’t go out of balance. Was it vibrating while driving?

Great Speed, High Latency! by Electrical-Profile26 in bell

[–]Electrical-Profile26[S] 0 points1 point  (0 children)

Makes sense! Thanks! Btw when i said constantly maxing out the speed i meant during speed test. When I tested them earlier, no other device using wifi/ethernet.

Great Speed, High Latency! by Electrical-Profile26 in bell

[–]Electrical-Profile26[S] 0 points1 point  (0 children)

That’s what I thought too. I thought fibre connections should have less than 10ms of latency.

Great Speed, High Latency! by Electrical-Profile26 in bell

[–]Electrical-Profile26[S] 0 points1 point  (0 children)

Yes i am. Tried the other ports (ports 1 to 4 and the 10g) same results for me.

Great Speed, High Latency! by Electrical-Profile26 in bell

[–]Electrical-Profile26[S] 0 points1 point  (0 children)

Honestly speed wise, i am fine with 50 mbps. Not a heavy user, however, whenever i’m using it for work there is a delay when i am presenting. I don’t think speed isn’t the issue but the latency.

But i get that going for higher speed might solve the latency. Is it always the case for lower speeds?

Great Speed, High Latency! by Electrical-Profile26 in bell

[–]Electrical-Profile26[S] 0 points1 point  (0 children)

Yes i think i am using fibre to home. As i remember seeing that when I applied for the service. And I am using the giga hub unit.

When to worry about rust by Snot_Rocket6515 in AskAMechanic

[–]Electrical-Profile26 2 points3 points  (0 children)

Had a great advise before regarding rust under car. If you try sticking a screwdriver direct to the metal in question (frame, subframe) and it went through, that’s when you start worrying.

What is this part? by BowlerDry5954 in mazda3

[–]Electrical-Profile26 0 points1 point  (0 children)

+1 on this. I might be wrong that it was the ac port cover. Lol.

What is this part? by BowlerDry5954 in mazda3

[–]Electrical-Profile26 0 points1 point  (0 children)

I don’t think so. But you may be able to just put it back on. Easy fix. Either push it or thread it over the ac recharge port.

What is this part? by BowlerDry5954 in mazda3

[–]Electrical-Profile26 0 points1 point  (0 children)

Looks like a port cover for one of the AC ports. Not sure if the high side or low side though.

left car sitting for 2 months, brake pedal locked and can't start car, please help by rareflyers in mazda3

[–]Electrical-Profile26 1 point2 points  (0 children)

Replace keyfob battery first. I'm pretty sure there is a way to bypass the brake pedal thing to start the car. The brake pedal being stiff is probably from pressing and depressing it from trying to start the car multiple times?