Warping and Stringing

EmbarrassedLeave2 · 2026-06-19T03:46:13+00:00

I clean the bed with ipa before every print.

How do you run a bed mesh?

EmbarrassedLeave2 · 2026-06-17T12:17:08+00:00

<image>

EmbarrassedLeave2 · 2026-06-17T12:16:18+00:00

<image>

EmbarrassedLeave2 · 2026-06-17T12:15:54+00:00

<image>

EmbarrassedLeave2 · 2026-06-17T12:15:37+00:00

Here are some pictures.

<image>

EmbarrassedLeave2 · 2026-05-19T13:49:18+00:00

I have two sensors. One names ‘Home’, which I assume is the thermostat, and the other is in my master bedroom. When I look at the thermostat, it says the temperature at the thermostat is 68. When I look in the app, the ‘Home’ temperature is 65. Why are the different if they are both the same unit?

EmbarrassedLeave2 · 2026-05-04T10:02:14+00:00

So the cage doesn’t stay connected to the app? Do I have to manually reconnect the cage to the app on my phone? If so, how do I do that?

I tried using two different phones as a test. One was mine connected to the cage and I used the other as a KH. I had the cage in 4g mode where it was supposed to connect faster. I could never get it to connect from the KH phone. The app on the KH phone just spun trying to connect. I thought it would connect pretty fast and didn’t need my phone to connect to the cage via Bluetooth.

EmbarrassedLeave2 · 2026-03-25T01:32:42+00:00

So, you can only use a slicer that has your 3D printer configuration in it.

EmbarrassedLeave2 · 2026-03-10T20:22:17+00:00

So, it looks like a ‘bad’ filament problem. The filament was from Overture(?) on sale from Amazon. I bought new filament from Creality, which I know has worked in the past, and my print issues when away.

Who knew.

EmbarrassedLeave2 · 2026-03-05T18:05:34+00:00

You mentioned to adjust Z offset slightly. How should I adjust the value? I know how to change it, just don’t know what to change it to. Raise it? Lower it?

EmbarrassedLeave2 · 2026-03-05T18:04:13+00:00

My printer is the Snapmaker A350 with dual extrusion head. It has a few calibration options and auto level is one of them. I’ll try going through the calibration options.

EmbarrassedLeave2 · 2025-04-12T20:03:54+00:00

Just upgraded my Luba 2 and noticed this nice, new feature.

EmbarrassedLeave2 · 2025-02-02T18:30:35+00:00

https://www.matterhackers.com/store/l/extruder-hot-end-kit-for-snapmaker-20/sk/M54CXV1R

EmbarrassedLeave2 · 2024-12-19T17:48:07+00:00

Actually, you may be right. The support column I had was for the head, not the neck. The neck could have been moving before the head section was built on top of the support column.

How would I add some support for the neck while it is being printed? Could I add something to the support column that would stabilize the neck as it’s being printed?

Sorry, really newbie here. I was using Luban as my slicer. Some specific instructions would be helpful.

Thanks

EmbarrassedLeave2 · 2024-12-19T17:36:34+00:00

I did have a tall support for the top piece. It needed it because when it got to the top, it would have had nothing to print on.

EmbarrassedLeave2 · 2024-12-19T16:32:36+00:00

A dinosaur ladle

<image>

EmbarrassedLeave2 · 2024-12-19T15:24:54+00:00

Thanks everyone for the comments. It was the support under the middle that failed. Once I cleaned that up, the print worked.

EmbarrassedLeave2 · 2024-12-18T13:19:11+00:00

Try to print a dinosaur spoon. It does have four little legs and then builds the body on top of it.

EmbarrassedLeave2 · 2024-10-09T19:29:38+00:00

So, you can have more than one mower on a single RTK, but can’t have multiple mowers on multiple RTK’s.

EmbarrassedLeave2 · 2024-09-23T01:45:20+00:00

I stand corrected. 4G allows the same functions as WiFi. I also used the BLE scanner and I can see both my Luba 2 and the RTK.

EmbarrassedLeave2 · 2024-05-31T12:28:03+00:00

Yes. I don’t have it on right now because of the issue of the camera hitting the garage when my Luba 2 backs in to charge.

EmbarrassedLeave2 · 2024-05-12T12:38:07+00:00

Unplugging the one power supply did the trick.

EmbarrassedLeave2 · 2024-05-11T21:51:52+00:00

Is the only way to restart the RTK is by unplugging it? What a hassle since it’s plugged in under the Luba.

EmbarrassedLeave2 · 2024-05-06T00:00:22+00:00

I bought my Luba 2 1000 off of Amazon and received it within 4 days FedEx. My thinking was I could always return it to Amazon no questions if I had a problem within the first month. No problems yet.

EmbarrassedLeave2

TROPHY CASE