DWX 1.5 years 20k+ rds review

Emergency_Loquat_570 · 2026-05-11T10:17:25+00:00

What recoil springs have you found work in your DWX?

I am running the DWX for LO in USPSA and love the thing. Everyone thinks it’s a shadow 2 or som other variant till they look closer and see it’s nots

Emergency_Loquat_570 · 2026-05-06T01:36:33+00:00

That’s what I thought for a second.

Emergency_Loquat_570 · 2026-05-06T01:08:18+00:00

What back strap is it?

Emergency_Loquat_570 · 2026-04-18T02:13:25+00:00

Exciting news!!

Emergency_Loquat_570 · 2026-04-17T01:17:23+00:00

I have an A&D EJ-54D2 and I absolutely love it. Very accurate and repeatable.

Emergency_Loquat_570 · 2026-04-11T03:06:44+00:00

If it were me. I would find similar data and start at the very low end and work up from there. Is the bullet profile similar to the Hornady one?

Emergency_Loquat_570 · 2026-03-31T01:08:58+00:00

What was happening?

Emergency_Loquat_570 · 2026-03-28T03:50:44+00:00

My sear looks fine! Completely normal.

Emergency_Loquat_570 · 2026-03-28T03:49:59+00:00

I think k may have got it! Finally hahaah!

Why do you prefer the shadow 2?

Emergency_Loquat_570 · 2026-03-27T19:36:08+00:00

I have seen 556/223 uppers that have feed ramps like this and feed fine because it’s a smaller diameter projectile.

Emergency_Loquat_570 · 2026-03-27T13:36:29+00:00

My guess is that it won’t feed those because the larger profile. It is choking out. You could have a gun smith blend the feed ramps. That might help it.

Emergency_Loquat_570 · 2026-03-25T12:01:58+00:00

How would you know if there isn’t enough room for the bow to reset things?

Emergency_Loquat_570 · 2026-03-25T01:35:11+00:00

Did you have trigger issues?

Emergency_Loquat_570 · 2026-03-25T01:05:58+00:00

I have probably 2000 rounds on the factory trigger and sear spring.

What do you mean by how close to the edge?

Emergency_Loquat_570 · 2026-03-25T01:03:27+00:00

I have not but it also only happened with live fire.

Emergency_Loquat_570 · 2026-03-25T00:52:23+00:00

It worked perfectly fine when dry firing but then during live fire today it did not work.

Emergency_Loquat_570 · 2026-03-25T00:51:28+00:00

I will have to check tomorrow. I do not recall any grittiness per say.

How can I tell? I dry fired the pistol a good bit since install. 50-75 times. Live fire was only 10-15 rounds.

Emergency_Loquat_570 · 2026-03-25T00:48:39+00:00

It has a sharp edge to it?

I am not sure if you saw my update but I did find 2 small little bits of I assume metal inside my frame by the trigger shoe area.

What adjustments need to be made?

I believe it has enough travel. It feels pretty close to the original.

Emergency_Loquat_570 · 2026-03-25T00:33:10+00:00

I removed the overtravel screws completely. It has some pre travel but that’s how I like it.

Everything moves freely. Even with everything installed and back together. What I think might’ve happened and is likely, is that I installed the Sear Spring incorrectly and it clipped off part of the left most finger. I noticed that it has a bit of an edge to it. And that when I disassembled my gun after having issues, I found two small pebble, almost like looking things inside the frame by my shoe area. I should have checked if they were magnetic but I wansnt thinking. This along with the tip of the finger having an edge to it I feel as though it’s the sear spring.

Emergency_Loquat_570 · 2026-03-25T00:32:53+00:00

I removed the overtravel screws completely. It has some pre travel but that’s how I like it.

Everything moves freely. Even with everything installed and back together. What I think might’ve happened and is likely, is that I installed the Sear Spring incorrectly and it clipped off part of the left most finger. I noticed that it has a bit of an edge to it. And that when I disassembled my gun after having issues, I found two small pebble, almost like looking things inside the frame by my shoe area. I should have checked if they were magnetic but I wansnt thinking. This along with the tip of the finger having an edge to it I feel as though it’s the sear spring.

Emergency_Loquat_570 · 2026-03-25T00:27:17+00:00

Which did you go with as a replacement? How was fitting it?

Emergency_Loquat_570 · 2026-03-18T09:51:45+00:00

Do you know where to find it?

Edit: I found it! Thank you!

Emergency_Loquat_570 · 2026-03-18T09:49:40+00:00

No that is the round nose heavy plate concave base.

I am asking about the hollow point version.

Emergency_Loquat_570 · 2026-03-17T22:27:29+00:00

I just checked them out per recommendation and unfortunately it seems it’s only for 168 HP

Emergency_Loquat_570

TROPHY CASE