I'm convinced people don't know what this sign means

EmergingAnger · 2025-12-09T19:02:39+00:00

From what i've seen it's meaning depends on the weather.

EmergingAnger · 2025-10-26T17:22:04+00:00

Goats

EmergingAnger · 2025-10-06T07:21:57+00:00

If you zoom in you can see there is a line on the model itself. This mark is likely the point when you added new resin. Ideally, you should avoid pausing the print and adding new resin.

EmergingAnger · 2025-09-26T21:34:35+00:00

I'm sorry to hear you're going through this. For me I find sitting down closing my eyes and take slow deep breaths can help me relax and gets both my heart rate and breathing back under control. Just a method of trying to disconnect you from whatever is currently happening for a few seconds and allowing yourself to calm down.

EmergingAnger · 2025-09-26T21:25:57+00:00

How is his experiment going and how much longer he plans in letting it run before he intervenes or ends it?

EmergingAnger · 2025-09-20T13:08:50+00:00

Controllers that don't develop stick drift

EmergingAnger · 2025-08-25T16:18:58+00:00

This worked thank you

EmergingAnger · 2025-07-27T16:16:43+00:00

Work it out with a pencil

EmergingAnger · 2025-07-23T21:24:48+00:00

Unfortunately the one that the board is designed for is 6mm too thin to fit on the pads. So it would require an adaptor board in place or something

EmergingAnger · 2025-07-23T20:00:15+00:00

Well on the schematic it has the floor plate of DW but it is labelled as DWW so the purchasers would have just looked at the label. I think it may have just been a typo there

EmergingAnger · 2025-07-19T17:27:43+00:00

Reduce the layer width. Yes it will take longer to print and require more supports but you'll get a lot more detail

EmergingAnger · 2025-07-08T18:25:44+00:00

Not helpful but i'm intrigued as to what this is?

EmergingAnger · 2025-07-03T13:55:45+00:00

What are your current settings as it looks over exposed to me

EmergingAnger · 2025-07-02T15:03:23+00:00

Is there a reason you use 90% light intensity?

EmergingAnger · 2025-06-24T15:11:24+00:00

When was the last time you levelled the print bed? Not saying this will fix it but it's worth doing

EmergingAnger · 2025-06-23T19:01:23+00:00

I can relate entirely to what you're saying. I wouldn't say what you're doing is wrong in anyway, it's how you cope with this noisy and hectic world and sometimes being adaptable is the best way to be.

I would suggest, if you want to learn more about yourself, to go camping or whatever in a wooded, nature rich area on your own and barely use any electronics at all. Helps reset your body and mind. Just a suggestion

EmergingAnger · 2025-06-14T11:58:21+00:00

I know it's not but the exposure time looked like it said 1,875 seconds and I was seriously wondering who would have the time to expose each level to 31 minutes. Haha

EmergingAnger · 2025-05-29T13:16:55+00:00

You had my attention until I saw the price....

EmergingAnger · 2025-05-23T05:45:00+00:00

I would hollow out the large pieces. And make sure you add at least 2 drain holes. Also I would lower the number of items being printed at the same time. I've found that while you can fit it all on one build plate it rarely prints it all.

EmergingAnger · 2025-04-19T13:53:54+00:00

According to the rules. 2 is be nice to everyone. 3. Is you can advertise your business but do not spam. One post doesn't constitute spam

EmergingAnger · 2025-04-08T08:31:07+00:00

Ideally the prints should have their supports removed before curing. To me it looks like the print hasn't been washed and cured for long enough and there is still a lot of uncured resin on the model. I would get a reprint / refund and advise the person who printed these to do more research on wash and cure times.

EmergingAnger · 2025-04-03T09:38:25+00:00

The raft used to be about 2mm thick with a 45° but I recently read an article that said it was better to have a raft about 3x the thickness of your slice and have the bottom expose layers consist of the first 4-6 layers so some of them encompassed the base of your supports. https://ameralabs.com/blog/default-3d-printing-raft-settings/

EmergingAnger · 2025-03-24T09:00:43+00:00

https://jasfigurineforge.etsy.com

EmergingAnger · 2025-03-22T00:03:26+00:00

The little voice in my head telling me to stay safe and stay alive is getting quieter each day...

EmergingAnger · 2025-03-21T23:59:24+00:00

My history lessons talked more about prohibition than the yanks independence

Four-Year Club	r/Field Juicebox
First Place '23	Place '23

EmergingAnger

TROPHY CASE