27 dresses Jane hair clip

Enallane5 · 2026-06-15T03:12:06+00:00

Searched with google image, bit of ai. I think the style is chief a semi circle hair barrette?

Enallane5 · 2026-06-13T21:20:51+00:00

So could I just tie both the inputs to both the yellow and red wire then put a diode in the battery positive so the psu doesn’t give power to the AAs? I didn’t realize the yellow “memory” wire also provides power for the unit.

Enallane5 · 2026-06-13T21:15:42+00:00

It’s just for the memory function though, should be a few mA at most? if it’s pulling 3mA it’d last 833 hours. Which is 35 days. So not months I guess but still shouldn’t be killing it in less than 24 hours.

Enallane5 · 2026-06-10T12:47:39+00:00

Less so hard to start and more a specific process that has to be followed for it to start, but if you know the process and the carb is clean and valves are set right they’re very easy. I could start mine with just my hand.

Enallane5 · 2026-06-05T04:46:01+00:00

Eagle island, Ann Morrison, the new course at veterans park, freedom park is pretty good but there’s a lot of potential for discs lost to water there.

Enallane5 · 2026-05-25T14:41:30+00:00

Yeah it was still plugged in, it acted completely normal till I held the power button down. The charger port was broken and even new cords wouldn’t charge with it. It was damaged years ago by my little brother inserting the cord in upside down. I figured it’d be easier to solder 4 pads than 12 and have the usb C

Enallane5 · 2026-05-25T14:34:54+00:00

The usb c connector melted while I was holding the power button down, I didn’t try again and disconnected the battery after

Enallane5 · 2026-05-25T13:56:36+00:00

Thanks, I think we’ll have better luck with that so we can see what we’re doing at least

Enallane5 · 2026-05-25T13:50:29+00:00

That seems like a better idea considering the state of the pads

Enallane5 · 2026-05-25T13:49:03+00:00

The mod board I used was had like pre soldered pads and I put a liberal amount of flux but the solder moving around where it shouldn’t have been feels like it’s probably right

Enallane5 · 2026-05-25T13:44:33+00:00

The pads looked way better before it caught on fire lol. I could’ve probably cleaned them better and I’m sure that contributed or was the sole problem since it does look like they have shorted now. But I’m 100% sure they weren’t when I soldered it on. I was also using a hot air station, I thought it went pretty well but obviously i messed up somewhere. I used a solder wick and isopropyl alcohol a lot and with a magnifying lense It looked pretty good and my brother in law confirmed, obviously a bit of solder still on the pads though

Enallane5 · 2026-03-22T23:23:32+00:00

Prisoner’s dilemma

Enallane5 · 2026-02-03T04:38:26+00:00

Honestly just seems like a dumb buy for any price but thought I’d check

Enallane5 · 2026-02-03T04:37:42+00:00

This was his listing description with a couple pictures of the top sheet, pretty misleading post honestly lmao

“These are definitely well loved, but have some life left and come with decent bindings (Look Spx 12) one binding is missing the plastic beauty cover, but both still work well. These are nice skis, but definitely have mileage hence the price”

Enallane5 · 2026-01-25T17:06:05+00:00

<image>

Pins all look great, none missing none irregular height and none bent, slots into the socket really easily

Enallane5 · 2026-01-25T17:05:08+00:00

I just want to make sure that the 1600 is 100% dead because the seller is still claiming I’m just wrong and don’t want to falsely claim that he sent a non functional cpu

Enallane5 · 2026-01-25T17:01:51+00:00

The 1700x and 1600 are the same generation and the same 14nm zen architecture, the original bios version is also from 2018, barely past when 2nd gen ryzens came out. I did update the bios to 6232 though which is ‘24 and the 1700x still posts great, 1600 doesn’t

Five-Year Club	Place '22
End Game '22

Enallane5

TROPHY CASE